DEUTSCHE NORM September 2005 DIN EN 1433 ics93.080.30 Supersedes April 2003 edition . Drainage channels for vehicular and pedestrian areas Classification ,design and testing requirements , marking and evaluation of conformity ( includesCorrigendum AC :2004 Amendment A1 :2005 ) English version of DIN EN 1433 :2002 AC :2004 A1 :2005 Entwasserungsrinnen fur Verkehrsflachen Klassifizierung ,Bau -und Prufgrundsatze ,Kennzeichnung und Beurteilung der Konformitat ( enthaltBerichtigung AC :2004 Anderung A1 :2005 ) National foreword This standard has been prepared by CEN /TC165 ' Wastewaterengineering' (Secretariat:Germany ),WG 4 Gullies and tops The responsible German body involved in its preparation was the Normenausschuss Wasserwesen ( Water Practice Standards Committee ),Technical Committee V Entwasserungsgegenstande . Annex ZA contains information on the conformity with the EU Construction Products Directive of drain - age channels made according to this standard .According to decision of the European Commission ,any manufacturer placing drainage channels on the market is responsible for declaring their pliance with the requirements of Annex ZA ,and thus for affixing of...
EUROPEAN STANDARD e14179-1 NORME EUROPEENNE EUROPAISCHE NORM July 2016 CS81.040.20 Supersedes EN 14179-1 :2005 English Version Glass in building - Heatsoaked thermally toughened soda lime silicate safety glass -Part 1 :Definition and description Verre dans la construction -Verre de silicate sodo - Glas im Bauwesen HeiBgelagertes thermisch calcique de securite trempe et traite Heat Soak -Partie vorgespanntes Kalknatron-Einscheibensicherheitsglas 1 :Definition et description Teil 1 :Definition und Beschreibung This European Standard was approved by CEN on 12 May 2016 . CEN members are bound to ply with the CEN /CENELECInternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration .Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member . This European Standard exists in three official versions ( English,French ,German ).A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manage...
bsN12420:2014 BSI Standards Publication Copper and copper alloys - Forgings bsi making excellence a habit BSEN12420:2014 National foreword This British Standard is the UK implementation of EN 12420 :2014 .It supersedes BS EN 12420 :1999 which is withdrawn . The UK participation in its preparation was entrusted to Technical Committee NFE /34/,Wrought and unwrought copper and copper alloys . A list of organizations represented on this mittee can be obtained on request to its secretary . This publication does not purport to include all the necessary provisions of a contract .Users are responsible for its correct application . The British Standards Institution 2014 .Published by BSI Standards Limited 2014 n9780580787454 ics77.150.30 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2014 . Amendments issued since publication Date Text affected bsn12420:2014 EUROPEAN STANDARD 12420 NORME EUROPEENNE EUROPAISCHE NORM June 2014 ics77.150.30 Supersedes EN 12420 :1999 English Version Copper and copper alloys -Forgings Cui...
BRITISH STANDARD BS EN 12167:1998 Copper and copper alloys Profiles and rectangular bar for general purposes The European Standard EN 12167 :1998 has the status of a British Standard ics77.150.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW bsen12167:1998 National foreword This British Standard is the English language version of EN 12167 :1998 published by the European Committee for Standardization ( CEN).Together with BS EN 12163 and BS EN 12164 it supersedes BS 2874 :1986 which is withdrawn . The UK participation in its preparation was entrusted by Technical Committee NFE34 ,Copper and copper alloys ,to Submittee NFE //1,Wrought and unwrought copper and copper alloys ,which has the responsibility to : aid enquirers to understand the text ; - presentto the responsible European mittee any enquiries on the interpretation ,or proposals for change ,and keep the UK interests informed ; monitor related international and European developments and promulgate them in the UK . A list of organizations represented on this submittee can be obtained on request to its secretary . Cross-references The British Standards which implement internatio...
企业秘密 ECE 欧洲经济委员会(ECE)汽车标准法规中文译本 REGULATION No .66 关于大型客车上层结构强度认证的统一规定 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF LARGE PASSENGER VEHICLES WITH REGARD TO THE STRENGTH OF THEIR SUPERSTRUCTURE 中国第一汽车集团公司技术中心 国家:欧洲经济员会(E. 源子:联合国1987年1月30日协议 E /ECE/324 E /ECE/TRANS/505 Rev ./Add.65/Amend.I 1997年12月3日 联合国协议 关于轮式车辆安装及/或用在轮式车辆上的装备及零部件 采用统一的技术法规以及满足这些法规的认证 相互认可的条件 (第2版,包括1995年10月16日开始生效的修正本) 附录65:66号法规 修正本1 对本法规原始版本的补充规定1:1997年9月3日生效 关于大型客车上层结构强度认证的统一规定 协议的原名: 有关采用机动车辆装备及零部件认证以及认证相互认可的统一条件的协议于1958年3月20日在日内瓦通过。 标题:大型客车上层结构的强度 第1版 法规号:66 1999年7月 第页 ...
E /ECE/324 E /ECE/TRANS/505 Rev ./Add./Rev.2 12 March 2009 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONS FOR WHEELED VEHICLES ,EQUIPMENT AND PARTS WHICH CAN BE FITTED AND /ORBE USED ON WHEELED VEHICLES AND THE CONDITIONS FOR RECIPROCAL RECOGNITION OF APPROVALS GRANTED ON THE BASIS OF THESE PRESCRIPTIONS * ( Revision2 ,including the amendments which entered into force on 16 October 1995 ) Addendum 89 :Regulation No .90 Revision 2 Incorporating all valid text up to : Supplement 5 to the series of amendments -Date of entry into force :7 December 2002 Supplement 6 to the series of amendments Date of entry into force :9 November 2005 Supplement 7 to the 01 series of amendments Date of entry into force :18 January 2006 Supplement 8 to the series of amendments Date of entry into force :2 February 2007 Supplement 9 to the 01 series of amendments -Date of entry into force :10 November 2007 Corrigendum I to Revision I of the Regulation ,subject of Depositary Notification .N.251.2008.TREATIES-1dated April 2008 Date of entry into force :12 March 2008 Supplement 10 to the series of amendments Date of entry into force :15 October 2008 UNIFORM PROVISIONS CO...
E /ECE/324 E /ECE/TRANS/505 Rev .2/Add.12H/Rev.1 17 January 2008 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONS FOR WHEELED VEHICLES ,EQUIPMENT AND PARTS WHICH CAN BE FITTED AND /ORBE USED ON WHEELED VEHICLES AND THE CONDITIONS FOR RECIPROCAL RECOGNITION OF APPROVALS GRANTED ON THE BASIS OF THESE PRESCRIPTIONS * ( Revision2 ,including the amendments which entered into force on 16 October 1995 ) Addendum 12H :Regulation No .13-H Revision 1 Incorporating all valid text up to : Corrigendum to the original version of the Regulation ,subject of Depositary Notification C .N.708.1999.TREATIES-1dated 6 August 1999 Corrigendum 2 to the original version of the Regulation ,subject of Depositary Notificatio C .N.897.2000.TREATIES-1 dated 27 September 2000 Corrigendum 3 to the original version of the Regulation ,subject of Depositary Notificatio C .N.784.2002.TREATIES-1 dated 1 August 2002 Corrigendum 4 to the original version of the Regulation ,subject of Depositary Notification C .N.364.2003.TREATIES-1 dated 8 May 2003 Supplement to the original version of the Regulation Date entry into force :27 December 2000 Supplement 2 to the original version of the ...
E /ECE/324/Rev./Add.12/Rev.7-E/ECE/TRANS/505/Rev.1/Add.12/Rev.7 4 August 2011 Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles , Equipment and Parts which can be Fitted and /orbe Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions ( Revision2 ,including the amendments which entered into force on 16 October 1995 ) Addendum 12 :Regulation No .13 Revision 7 Incorporating all valid text up to : series of amendments Date of entry into force :July 2008 Supplement 5 to the 10 series of amendments -Date entry into force :15 October 2008 Corrigendum the Supplement to Revision 6 -Erratum Corrigendum 2 to the Supplement to Revision 6 -Erratum Supplement to the series of amendments -Date of entry into force :22 July 2009 Corrigendum I to Revision 6 subject of Depositary Notification .N.248.2009.TREATIES-3dated 30 April 2009 Corrigendum to Revision 6 -Erratum ( Russianonly ) Supplement 2 to the series of amendments -Date entry into force :24 October 2009 Corrigendum to Revision 6 subject of Depositary Notification C .N.563.2009.TREATIES-5dated 17 September 2009 C...
E /ECE/324 E /ECE/TRANS/505 Rev ./Add.12/Rev.6/Amend.4 30 December 2009 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONSFOR WHEELED VEHICLES ,EQUIPMENT AND PARTS WHICH CAN BE FITTEDAND /ORBE USED ON WHEELED VEHICLES AND THE CONDITIONS FOR RECIPROCAL RECOGNITION OF APPROVALS GRANTED ON THE BASIS OF THESE PRESCRIPTIONS * ( Revision2 ,including the amendments that entered into force on 16 October 1995 ) Addendum 12 :Regulation No .13 Revision 6 -Amendment 4 Supplement 2 to the 11 series of amendments :Date of entry into force :24 October 2009 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF VEHICLES OF CATEGORIES M .N AND O WITH REGARD TO BRAKING UNITED NATIONS * /Formertitle of the Agreement Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts ,done at Geneva on 20 March 1958 . ge.09 /ECE/324 E /ECE/TRANS/505 Rev .1 /Add.12/Rev.6/Amend.4 Regulation No 13 page 2 Add new paragraphs 2.35. and 2.36. ,to read "2.35. Subject trailer "is a trailer representative the trailer type for which type approval is sought 2.36. The " brakefactor ( )"isthe input to output am...