This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E3225-20 INTERNATIONAL Standard Practice for Performing a Liquid Test of Spill Prevention Equipment and Containment Sumps Used for Interstitial Monitoring of Piping by Visual Examinationt This standard is issued under the fixed designation E3225;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope responsibility of the user of this standard to establish appro- 1.1 Spill prevention equipment and containment sumps are priate safety health and environmental practices and deter- tested periodically to ensure the equipment is liguid right by mine the applicabiliry of regulatory limitations prior to use. using vacuum pressure or liquid testing pursuant to United Hazards known to this practice are identified in Section 8. States of America federal regulations found in 8 40 CFR 1.8 This international standard was developed in accor- 280.35. dance with internationally recognized principles on standard- ization es...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E3222-20a INTERNATIONAL Standard Classification for Determination of High-frequency Impact Sound Ratings1 This standard is issued under the fixed designation E3222:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope Ceiling Assemblies and Associated Support Structures 1.1 This classification provides methods for calculating E2179 Test Method for Laboratory Measurement of the single-number ratings of high-frequency impact sound Effectiveness of Floor Coverings in Reducing Impact transmission based on one-third-octave-band impact sound Sound Transmission Through Concrete Floors pressure levels generated by the standard tapping machine as 3.Terminology described in Test Methods E492 E1007 and E2179. 3.1 The following terms used in this classification have 1.2 This classification defines ratings that are not defined in specific meaning that are defined in Terminology C634:aver- other standards.Within their p...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:E3211-22 INTERNATIONAL StandardPracticefor Selection,Integration,andVerificationofActiveVehicle BarrierSafetyDevices1 jo eaf oq sapu uopeulisap ou umojo <jmpouui oqunu oq :11g uogeu3lsap paxy oq Japun pansst s pmpues suL renodeau o uorstau stl oq ours suepo peuopo ue sapeput (a) uosds dussuxdns original adoption or, in the case o revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
1. Scopevehicles that are stopped.The presence of “casual pedestrians 1.1 This practice is intended to provide methods forshall be kept away from the movable elements of the AVBS. selecting,integrating,and verification of active vehicle barrier1.6 This practice is not intended to address any of the safety devices so that vehicle barrier systems are reliably and following: safely controlled when in operation.1.6.1 Overall performance of vehicle barrier systems or 1.2 There are a number of risks associated with the opera-effectiveness as a barrier against any vehicles (see Test Method tion and use of active vehicle barrier systems (AVBS). One of F2656/F2656M). the risks is that of undesired collision between an active vehicle1.6.2 Impact energy able to be withstood by vehicle barrier barrier (AVB) and an authorized vehicle. Such risks can be systems. minimized through proper design, construction, installation,1.6.3 Serviceability of barrier systems. operation, and training in the use of such systems.1.6.4 Selection of vehicle barrier systems for any particular 1.3 The proper selection, installation, and use of safetyuse. devices that will prevent an AVBS from activating or deploying1.6.5 Pedestrian Detection Safery De...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E3090/E3090M-20 INTERNATIONAL Standard Test Methods for Strength Properties of Metal Ceiling Suspension Systems This standard is issued under the fixed designation E3090/E3090M;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval. A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. INTRODUCTION In the past mechanical properties of metal ceiling suspension systems have been buried in other standards such as Specification C635 and Practice E580.This test method is an attempt to pull all testing requirements into one document. 1.Scope 2.Referenced Documents 1.1 These test methods cover metal ceiling suspension 2.1 ASTM Standards:2 systems used primarily to support acoustical tile acoustical C634 Terminology Relating to Building and Environmental lay-in panels or suspended T-bar type ceiling systems. Acoustics 1.2 These test methods cover the determination of strength C635 Specification for Manufacture Performance and Test- properties of suspended ceiling grid system...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standartis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E3068-20 TU INTERNATIONAL Standard Test Method for Contact Measurement of Backface Deformation in Clay Backing During Body Armor Testing' This standard is issued under the fixed designation E3068:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope responsibility of the user of this standard to establish appro- 1.1 This test method describes test methods for the contact priate safety health and environmental practices and deter- measurement of backface deformation (BFD)in clay backing mine the applicability of regulatory limitations prior to use. caused by a test threat that produces a partial penetration in a 1.9 This international standard was developed in accor- body armor test item. dance with internationally recognized principles on standard- ization established in the Decision on Principles for the 1.2 This test method is applicable to testing of planar and Development of International Standards Gu...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standartis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E3005-20 TU INTERNATIONAL Standard Terminology for Body Armor' This standard is issued under the fixed designation E3005;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope 3.Terminology 1.I The scope of this terminology is to provide a standard accessory n-a body armor ponent that is detachable or terminology for body armor providing protection against removable from the body armor and is intended to provide ballistic threats stabbing fragmentation blunt impact or a extended area of coverage protection against threats that may bination of threats. include ballistic threats stabbing fragmentation blunt 1.2 The intent of this terminology is to have terms impact or a bination of threats. abbreviations and formulas that are applicable across federal DIscussIoN-Accessories are typically attachments to tactical body agencies law enforcement and corrections agencies testing armor providing protectio...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2936-20 INTERNATIONAL Standard Guide for Contractor Self-Assessment for U.S.Government Asset Management Systems1 This standard is issued under the fixed designation E2936;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. INTRODUCTION The purpose of this standard is to provide guidance for a Contractor Self-Assessment (CSA) program that addresses the requirement of Federal Acquisition Regulation (FAR)52.245-1(Govern- ment Property)that contractors perform periodic reviews surveillances self-assessments or audits. This guide is intended to assist contractors in developing a CSA program that provides reasonable assurance of the effectiveness of the contractor's government asset management system to internal and external stakeholders.Use of this guide should enable contractors to objectively evaluate government asset management system risks discover deficiencies identify the root causes and implement corrective a...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E276-21 INTERNATIONAL Standard Test Method for Particle Size or Screen Analysis at 4.75 mm (No.4)Sieve and Finer for Metal-Bearing Ores and Related Materials' This standard is issued under the fixed designation E276:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (8)indicates an editorial change since the last revision or reapproval. 1.Scope 3.Terminology 1.1 This test method covers the determination of the particle 3.1 Definitions: size distribution by screen analysis dry or wet of metal- 3.1.1 For definitions of terms used in this test method refer bearing ores and related materials at 4.75 mm (No.4)sieve and to Terminology E135. finer. 1.2 Units-The values stated in SI units are to be regarded 4.Summary of Test Method as standard.The values given in parentheses after SI units are 4.1 The sample is passed through a bank of sieves by provided for information only and are not considered standard.agitation.The dry screening technique described in this test 1.3 This standard does ...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2661/E2661M-201 INTERNATIONAL Standard Practice for Acoustic Emission Examination of Plate-like and Flat Panel Composite Structures Used in Aerospace Applications' This standard is issued under the fixed designation E2661/E2661M:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval. A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. g'NOTE-An editorial change was made to the References section in November 2020. 1.Scope* 1.7 This standard does not purport to address all of the 1.1 This practice covers acoustic emission (AE)examina- safety concerns if any associated with its use.It is the tion or monitoring of panel and plate-like posite structures responsibility of the user of this standard to establish appro- made entirely of fiber/polymer posites. priate safety health and environmental practices and deter- mine the applicability of regulatory limitations prior to use. 1.2 The AE examination detects emission sources and 1.8 This international standard was d...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2649-20 TU INTERNATIONAL Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy This standard is issued under the fixed designation E2649:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope ization established in the Decision on Principles for the 1.1 This test method covers procedures for using a spark Development of International Standards.Guides and Re- emission spectroscope to determine the concentration of argon mendations issued by the World Trade Organization Technical gas in the space between the lites of a sealed insulating glass Barriers to Trade (TBT)Committee. unit. 2.Referenced Documents 1.2 This is a non-destructive test method. 2.1 ASTM Standards:2 1.3 This test method shall be used only in a controlled C162 Terminology of Glass and Glass Products laboratory environment. C717 Terminology of Building Seals and Sealant...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2579-20 An American National Standard INTERNATIONAL Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics This standard is issued under the fixed designation E2579:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope 1.10 This standard does not purport to address all of the 1.1 This practice describes procedures for specimen prepa- safery concerns if any associated with its use.It is the ration and mounting when testing wood products to assess responsibility of the user of this standard to establish appro- flames spread and smoke development as surface burning priate safery health and environmental practices and deter- characteristics using Test Method E84 or Test Method E2768. mine the applicability of regulatory limitations prior to use. 1.1.1 Test Method E2768 uses the same test equipment as 1.11 This international standard was developed in ...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2296-21 INTERNATIONAL Standard Practice for Silver Corrections in Metal Bearing Ores Concentrates and Related Metallurgical Materials by Fire Assay Slag Recycling and Cupel Proof Gravimetry' This standard is issued under the fixed designation E2296:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope E882 Guide for Accountability and Quality Control in the 1.1 This practice covers the silver loss correction utilizing Chemical Analysis Laboratory slag recycling and cupellation of proof silver during the fire 2.2 ISO Documents:3 assay of metal bearing ores concentrates and related metal- ISO 35:2006 Certification of Reference Materials-General lurgical materials. and Statistical Principles 1.2 Units-The values stated in SI units are to be regarded ISO 10378:2016 Copper Sulfide Concentrates- as standard.No other units of measurement are included in this Determination of Gold and Silver Contents-Fire Assay s...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2295-21 INTERNATIONAL Standard Practice for Fire Assay Silver Corrections in Analysis of Metal Bearing Ores Concentrates and Related Metallurgical Materials by Silver Determination in Slags and Cupels This standard is issued under the fixed designation E2295:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope E50 Practices for Apparatus Reagents and Safety Consid- 1.1 This practice covers the determination of silver correc- erations for Chemical Analysis of Metals Ores and tions for fire assay of metal bearing ores concentrates and Related Materials related metallurgical materials using the spent slags and cupels E135 Terminology Relating to Analytical Chemistry for from the fire assay process by gravimetry and atomic absorp- Metals Ores and Related Materials tion spectrophotometry. E882 Guide for Accountability and Quality Control in the Chemical Analysis Laboratory 1.2 The test methods appear in the f...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E2177-20 INTERNATIONAL Standard Test Method for Measuring the Coefficient of Retroreflected Luminance (RL) of Pavement Markings using the Bucket Method in a Condition of Wet Recovery This standard is issued under the fixed designation E2177;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript cpsilon (a)indicates an cditorial change sincc the last revision or rcapproval. 1.Scope 1.6 This standard does not purport to address all of the 1.1 This test method covers the measurement of the wet safety concerns if any associated with its use.It is the retroreflective (R properties of horizontal pavement marking responsibility of the user of this standard to establish appro- materials such as traffic stripes and road surface symbols priate safety health and environmental practices and deter- using a portable retroreflectometer that can be placed on or mine the applicability of regulatory limitations prior to use. before the road marking to measure the retroreflection at the 1.7 This international s...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committe. Designation:E2016-20 INTERNATIONAL StandardSpecificationfor Industrial WovenWireCloth1 Thisstandards i nderthefix designation 016;thenbemmdiatelyfollwing thedesignatinndicates th yea f original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval. INTRODUCTION Industrial wire cloth can be produced in many thousands of binations of size and shape of opening, wire diameter, type of weave, and metal. This specification covers woven wire cloth for industrial use, including the separation of particles. Its purpose is to introduce standard terms and definitions, to note the normal range of specifications woven, and to establish tolerances and requirements. This specification excludes sieve cloth from its scope, since this is covered under Specification E11. If a user has a specific application for industrial wire cloth that is not within the scope of this specification, it is remended that the wire cloth supplier be consulted. 1. Scope*2.Referenced Documents 1.1 This specification covers industrial woven wire fabric,2.1 ASTM Standards:2 referred to as wire cloth,for general use including the A510/A510M Specification for GeneralRequirements for separation of particles.Wire cloth can be made of any primary Wire Rods and Coarse Round Wire, Carbon Steel, and metal or metal alloy wire that is suitable for weaving. This Alloy Steel
A555/A555M Specification for General Requirements for wire cloth: filter cloth or dutch weave (see Appendix X1), Stainless Steel Wire and Wire Rods fourdrinier and c...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E1839-20 INTERNATIONAL Standard Practice for Efficacy of Slimicides for the Paper Industry-Bacterial and Fungal Slime This standard is issued under the fixed designation E1839;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope 2.2 TAPPI Standard: T 205 Forming Handsheets for Physical Tests of Pulp 1.1 This practice presents a procedure to evaluate the 2.3 CFR Standard: efficacy of slimicides for the control of bacterial and fungal 40 CFR Part 160 Good Laboratory Practice Standards slimes in paper mill systems and their counterparts. 1.2 It is the responsibility of the investigator to determine 3.Terminology whether Good Laboratory Practices (GLP)are required and to 3.1 For definitions of terms related to this practice see follow them where appropriate (40 CFR 160). Terminology E2756. 1.3 The values stated in SI units are to be regarded as 3.2 Definitions: standard.No other units of measurement are inc...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E1728/E1728M-20 INTERNATIONAL Standard Practice for Collection of Settled Dust Samples Using Wipe Sampling Methods for Subsequent Lead Determination This standard is issued under the fixed designation E1728/E1728M:the number immediately following the designation indicates the year of original adoption or.in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval. A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope Development of International Standards Guides and Re- 1.1 This practice covers the collection of settled lead- mendations issued by the World Trade Organization Technical containing dust on surfaces using the wipe sampling method. Barriers to Trade (TBT)Committee. These samples are collected in a manner that will permit 2.Referenced Documents subsequent extraction (see Practices E1644 and E1979)and determination of lead using laboratory analysis techniques such 2.1 ASTM Standards:2 as atomic spectrometry (see Test Methods E3193/E3193M and D1356 Terminology Relating to Sampling and Analysis of E3203)or electroanalysis (see Practice E2051)....

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E1606-20 INTERNATIONAL Standard Practice for Electromagnetic (Eddy Current)Examination of Copper and Aluminum Redraw Rod for Electrical Purposes' This standard is issued under the fixed designation E1606:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope* 2.Referenced Documents 1.1 This practice covers the procedures that shall be fol- 2.1 ASTM Standards:2 lowed in electromagnetic (eddy current)examination of copper E543 Specification for Agencies Performing Nondestructive and aluminum redraw rods for detecting discontinuities or Testing imperfections of a severity likely to cause failure or markedly E1316 Terminology for Nondestructive Examinations impair surface quality of the rod.These procedures are E2884 Guide for Eddy Current Testing of Electrically Con- applicable for continuous lengths of redraw rod in diameters ducting Materials Using Conformable Sensor Arrays from 4 to 13%in.(6.4 to 35 mm)sui...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E1568-21 INTERNATIONAL Standard Test Method for Determination of Gold in Activated Carbon by Fire Assay Gravimetry This standard is issued under the fixed designation E1568:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (8)indicates an editorial change since the last revision or reapproval. 1.Scope erations for Chemical Analysis of Metals Ores and 1.1 This test method covers the determination of gold in Related Materials activated carbon by fire assay collection and gravimetric E135 Terminology Relating to Analytical Chemistry for measurement.It covers the range of 15 ug/g to 5000 ug/g gold. Metals Ores and Related Materials E173 Practice for Conducting Interlaboratory Studies of 1.2 Units-The values stated in SI units are to be regarded Methods for Chemical Analysis of Metals (Withdrawn as the standard.No other units of measurement are included in 1998)3 this standard. E276 Test Method for Particle Size or Screen Analysis at 1.3 This standard does not purport to address all of...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:D8123-22 INTERNATIONAL Standard Test Methods for Measuring the Opening Size of Geohazard Nettings1 This standard is issued under the fixed designation D8123:the number immediately following the designation indicates the year of original adoption or in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope 1.4 This standard does not purport to address all of the 1.1 These test methods are index tests to measure the safety concerns if any associated with its use.It is the opening size of a geohazard netting or its ponents or both responsibility of the user of this standard to establish appro- as it has been manufactured.They can be used for estimating priate safety health and environmental practices and deter- the largest size of rock or other object that may pass through an mine the applicability of regulatory limitations prior to use. individual opening in the geohazard netting without transfer- 1.5 This international standard was developed in accor- ring load to the wire mesh or wire net and may ...