This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standartis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F2019-20 INTERNATIONAL Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP)Using the UV-Light Curing Method1 This standard is issued under the fixed designation F2019;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (g)indicates an editorial change since the last revision or reapproval. 1.Scope* 2.Referenced Documents 1.1 This practice covers the procedures for the reconstruc- 2.1 ASTM Standards:2 tion of pipelines and conduits (4 to 72 in.(100 to 1830 mm) D543 Practices for Evaluating the Resistance of Plastics to diameter)by the pulled-in place installation of a resin- Chemic...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F2009-20 INTERNATIONAL Standard Test Method for Determining the Axial Disassembly Force of Taper Connections of Modular Prostheses This standard is issued under the fixed designation F2009 the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope 3.Summary of Test Method 1.1 This test method establishes a standard methodology for 3.1 The axial disassembly test method provides a means to determining the force required under laboratory conditions to measure the axial locking strength of the taper connection for disassemble tapers of implants that are otherwise not intended modular prostheses. to release.Some examples ...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1917-201 INTERNATIONAL Standard Consumer Safety Performance Specification for Infant Bedding and Related Accessories This standard is issued under the fixed designation F1917:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. E'NOTE-Subsection 9.2 was corrected editorially in November 2020. INTRODUCTION This consumer safety performance specification addresses incidents associated with infant bedding and related accessories identified by the U.S.Consumer Product Safety Commission (CPSC). In response to incident data piled by the CPSC this specification attempts to minimize the following hazards:entanglement strang...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standardis Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1917-20 INTERNATIONAL Standard Consumer Safety Performance Specification for Infant Bedding and Related Accessories This standard is issued under the fixed designation F1917;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. INTRODUCTION This consumer safety performance specification addresses incidents associated with infant bedding and related accessories identified by the U.S.Consumer Product Safety Commission (CPSC). In response to incident data piled by the CPSC this specification attempts to minimize the following hazards:entanglement strangulation asphyxiation.This specification is intended to cover norma...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1733-20 An American National Standard INTERNATIONAL Standard Specification for Butt Heat Fusion Polyamide(PA)Plastic Fitting for Polyamide(PA)Plastic Pipe and Tubing' This standard is issued under the fixed designation F1733:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope* D4066 Classification System for Nylon Injection and Extru- 1.1 This specification covers polyamide (PA)butt fusion sion Materials (PA) fittings for use with polyamide pipe (IPS and Metric)and D6779 Classification System for and Basis of Specification tubing (CTS).Included are requirements for materials for Polyamide Molding and Extrusi...

This international standard was developed in accordance with internationally recognized prineiples on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1667-20 INTERNATIONAL Standard Specification for Driven Fasteners:Nails Spikes and Staples1 This standard is issued under the fixed designation F1667:the number immediately following the designation indicates the year of original adoption or in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon(g)indicates an editorial change since the last revision or reapproval. The Commercial and Government Entiry (Cage)Code for ASTM:81346. 1.Scope* A153/A153M Specification for Zinc Coating (Hot-Dip)on 1.1 This specification covers nails spikes staples and other Iron and Steel Hardware driven fasteners as listed in Table I. A641/A641M Specification for Zinc-Coated (Galvanized) Carbon Steel Wire NoTE 1-Fastener ductility information is presented in Table 2 and B695 Specification for Coatings of...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1667/F1667M-21a INTERNATIONAL Standard Specification for Driven Fasteners:Nails Spikes and Staples1 This standard is issued under the fixed designation F1667/F1667M:the number immediately following the designation indicates the year of original adoption or.in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval. A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. The Commereial and Government Entiry (Cage)Code for ASTM:81346. 1.Scope* 2.Referenced Documents 1.1 This specification covers nails spikes staples and other 2.1 ASTM Standards:2 driven fasteners as listed in Table I. A153/A153M Specification for Zinc Coating (Hot-Dip)on Iron and Steel Hardware NorE 1-Fastener ductility information is presented in Table 2 and A641/A641M Specification for Zinc-Coated (Gal...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standartis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1611-20 INTERNATIONAL Standard Specification for Intramedullary Reamers This standard is issued under the fixed designation F1611;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope F983 Practice for Permanent Marking of Orthopaedic Im- 1.1 This specification provides requirements for material plant Components dimensions and tolerances finish and marking and care and F1264 Specification and Test Methods for Intramedullary handling for reamers intended to cut a cylindrical path along Fixation Devices the medullary canal of diaphyseal bone. 3.Terminology 1.2 Intramedullary reamers are monly used to prepare...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1575/F1575M-21 INTERNATIONAL Standard Test Method for Determining Bending Yield Moment of Nails1 This standard is issued under the fixed designation F1575/F1575M:the number immediately following the designation indicates the year of original adoption or.in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval. A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope* 3.Terminology 1.1 This test method covers procedures for determining the 3.1 Definitions of Terms Specific to This Standard: bending yield moment of nails when subjected to static 3.1.1 bending yield moment-the moment determined from loading.It is intended only for nails used in engineered the load-deformation curve that is intermediate between the connection applications in which a required conne...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1554-20 INTERNATIONAL Standard Specification for Anchor Bolts Steel 36 55 and 105-ksi Yield Strength1 This standard is issued under the fixed designation F1554:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope* 2.Referenced Documents 1.1 This specification covers straight bent headed and 2.1 ASTM Standards:2 headless anchor bolts (also known as anchor rods)made of A6/A6M Specification for General Requirements for Rolled carbon medium carbon boron alloy or high-strength low- Structural Steel Bars Plates Shapes and Sheet Piling alloy steel.It provides for anchor bolts in three strength grades A194/A194M Spec...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1472-20a INTERNATIONAL Standard Specification for Wrought Titanium-6Aluminum-4Vanadium Alloy for Surgical Implant Applications (UNS R56400)1 This standard is issued under the fixed designation F1472:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope* E1447 Test Method for Determination of Hydrogen in Tita- 1.1 This specification covers the chemical mechanical and nium and Titanium Alloys by Inert Gas Fusion Thermal metallurgical requirements for wrought annealed titanium- Conductivity/Infrared Detection Method 6aluminum-4vanadium alloy (UNS R56400)to be used in the E1941 Test Method for Determination of Carb...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1359/F1359M-22 INTERNATIONAL Standard Test Method for Liquid Penetration Resistance of Protective Clothing or Protective Ensembles Under a Shower Spray While on a Manikin This standard is issued under the fixed designation F1359/F1359M:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval. A superscript epsilon (e)indicates an editorial change since the last revision or reapproval. INTRODUCTION Personnel in industry and emergency response can be exposed to numerous liquids capable of causing harm upon contact with the human body.These liquids may include chemicals contaminated blood or body fluids and other hazardous liquids.The deleterious effects of different chemicals can range from acute trauma such as skin irritation and burn to chronic degenerative disease such as cancer.Biological-based hazard liquids may include various liquid-borne pathogens capable of causing infection directly or with non-intact skin.Since engineering controls cannot eliminate all possible exposures attention is often placed on reducing the potential for direct skin contact through the use of protective clothing. Protective clothing is available in a variety of constructions configurations and materials and is designed to provide various levels of protection against many hazards.Protective clothing offering the highest level of chemical protection is constructed to prevent any contact of solid liquid or gaseous chemicals with the wearer.Test Method F1052 evaluates the integrity and construction of the vapor protective...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1356-22 INTERNATIONAL Standard Guide for Irradiation of Fresh Frozen or Processed Meat and Poultry to Control Pathogens and Other Microorganisms' This standard is issued under the fixed designation F1356:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (8)indicates an editorial change since the last revision or reapproval. INTRODUCTION The purpose of this guide is to present information on the use of ionizing radiation in treating fresh frozen or processed meat and poultry products to eliminate or reduce the numbers of vegetative pathogenic microorganisms and parasites and to extend the refrigerated shelf-life of those products by reducing the numbers of spoilage microorganisms. Thi...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1250-20 An American National Standard INTERNATIONAL Standard Specification for Stationary Upright and Recumbent Exercise Bicycles and Upper and Total Body Ergometers' This standard is issued under the fixed designation F1250;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (s)indicates an editorial change since the last revision or reapproval. INTRODUCTION The goal of this specification is to promote proper design and manufacturing practices for stationary upright and recumbent exercise bicycles and ergometers.Through these specifications this specifi- cation aims to assist designers and manufacturers in reducing the possibility of injury when these products are used in accordance wit...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standartis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1165-20 INTERNATIONAL Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts This standard is issued under the fixed designation F1165:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope E691 Practice for Conducting an Interlaboratory Study to 1.1 This test method covers measuring the angular separa- Determine the Precision of a Test Method tion of secondary images from their respective primary images as viewed from the design eye position of an aircraft transpar- 3.Terminology (see Fig.I) ency.Angular separation is measured at 49 points within a 20 3.1 angular displa...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1148-20 NTERNATIONAL Standard Consumer Safety Performance Specification for Home Playground Equipment This standard is issued under the fixed designation F1148:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (E)indicates an editorial change since the last revision or reapproval. 1.Scope 1.3 Methods of identifying products that ply with this 1.1 This consumer safety specification provides safety re- consumer safety specification are given.The illustrations of quirements for various types of home playground equipment home playground equipment shown in Figs.A1.1-A1.4 are for intended for use by children aged from over 18 months through informational purposes only and are not intended...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standartis.Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:F1091-20 INTERNATIONAL Standard Specification for Wrought Cobalt-20Chromium-15Tungsten-10Nickel Alloy Surgical Fixation Wire (UNS R30605) This standard is issued under the fixed designation F1091;the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (e)indicates an editorial change since the last revision or reapproval. 1.Scope* Determine Conformance with Specifications 1.1 This specification covers the chemical mechanical and F86 Practice for Surface Preparation and Marking of Metal- metallurgical requirements for the manufacture of wrought lic Surgical Implants cobalt-20chromium-15tungsten-10nickel surgical fixation F90 Specification for Wrought Cobalt-20Chromium- wire. 15Tungsten-10Nick...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E561-21 INTERNATIONAL Standard Test Method for Ka Curve Determination' This standard is issued under the fixed designation E561:the number immediately following the designation indicates the year of original adoption or.in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope* Development of International Standards Guides and Re- 1.1 This test method covers the determination of the mendations issued by the World Trade Organization Technical resistance to fracture of metallic materials under Mode I Barriers to Trade (TBT)Committee. loading at static rates using either of the following notched and 2.Referenced Documents precracked specimens:the middle-cracked tension M(T)speci- men or the pact tension...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E542-22 INTERNATIONAL Standard Practice for Gravimetric Calibration of Laboratory Volumetric Instruments This standard is issued under the fixed designation E542:the number immediately following the designation indicates the year of original adoption or in the case of revision the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (8)indicates an editorial change since the last revision or reapproval. 1.Scope 1.4 This standard may be used for the calibration of volu- 1.1 This practice covers procedures for use in the calibration metric instruments made from materials of glass plastic of volumetric instruments that include glassware plasticware various stable metals or any other stable materials provided appropriate volumetric coefficients of expansions are available. and laboratory standards that are in...

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards Guides and Remendations issued by the World Trade Organization Technical Barriers to Trade (TBT)Committee. Designation:E3334-22 INTERNATIONAL Standard Test Method for Acidity in Ethanol and Ethanol Solutions1 This standard is issued under the fixed designation E3334:the number immediately following the designation indicates the year of original adoption or in the case of revision.the year of last revision.A number in parentheses indicates the year of last reapproval.A superseript epsilon (s)indicates an editorial change since the last revision or reapproval. 1.Scope 2.Referenced Documents 1.1 This test method covers the determination of acidity as 2.1 ASTM Standards:2 acetic acid in ethanol and ethanol solutions.This test method D770 Specification for Isopropyl Alcohol may be applied to ethanol samples containing very little water D1193 Specification for Reagent Water (dehydrated alcohols)to solutions with significant water (low D7795 Test Method for Acidity in Ethanol and Et...