TECHNICAL ISO/TR REPORT 15608 Fourth edition 2017-02 Welding-Guidelinesforametallic materialsgroupingsystem Soudage - Lignes directrices pour un systeme de groupement des materiaux metalliques iTehSTANDARDPREVIEW (standards.iteh.ai) ISO/TR 15608:2017 htps//standards.itehai/catalog/standards/sist/586d88312332-4fc8-9d74- 820bfb682c96/so-tr-15608-2017 ISO/TR 15608:2017(E) Reference number ISO 2017
ISO/TR 15608:2017(E) iTehSTANDARDPREVIEW (standards.iteh.ai) ISO/TR 15608:2017 htps/standards.ichai/cataogstandads/st586d883123324f8-9d74 820bfb682c96/so-tr-15608-2017 COPYRIGHTPROTECTEDDOCUMENT @ ISO 2017 Published in Switzerland Al rightsreserved Unless otherwise specified no part of this publication may be reproduced or utilized otherwise in any form or by any means electronic or mechanical including photocopying or posting on the internet or an intranet without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 ▪ CP 401 CH-1214 Vernier Geneva Switzerland Tel. 41 22 749 01 11 Fax 41 22 749 09 47 copyright@ ii @ ISO 2017 All rights reserved
ISO/TR15608:2017(E) Contents Page Foreword iv Scope. 1 2 Normative references 1 3 Terms and definitions. 1 4 Grouping system for steels. 1 5 Grouping system for aluminium and aluminium alloys. 4 6 Grouping system for copper and copper alloys. 4 7 Grouping system for nickel and nickel alloys. 5 8 Grouping system for titanium and titanium alloys. 5 9 Grouping system for zirconium and zirconium alloys. 6 10 Grouping system for cast irons. 6 Bibliography 7 iTehSTANDARDPREVIEW (standards.iteh.ai) ISO/TR 15608:2017 htps//standards.itehai/catalog/standards/sist/586d88312332-4fc8-9d74- 820bfb682c96/so-tr-15608-2017 @ ISO 2017 All rights reserved i
ISO/TR 15608:2017(E) Foreword bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical mittees. Each member body interested in a subject for which a technical mittee has been established has the right to be represented on that mittee. International organizations governmental and non-governmental in liaison with ISo also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives Part 2 (see Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISo list of patent declarations received (see Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specificterms and expressions related to conformity assessment as wellasinformationabout SO'sadheencettheWRdTradeQiganization(WTo) principles in the Technical Barriers to Trade (TBT) see the following URL: (standards.iteh.ai) This document was prepared by Techinical CommitteeISO71℃44 Welding and allied processes Submittee SC 10 Quality management in the field of welding. ISO/TR156082017 This fourth edition cancelsand replaresitheithird edition:(ISO/TR15608:2013)§which has been revised and contains the following changes: 820bfb682c96/so-tr-15608-2017 a) the grouping system for steels has been revised (Clause 2); b) the Bibliography has been updated and the document editorially revised. Requests for official interpretations of any aspect of this document should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A plete listing of these bodies can be found at iv @ ISO 2017 All rights reserved
TECHNICALREPORT ISO/TR 15608:2017(E) Welding-Guidelinesforametallicmaterialsgrouping system 1Scope This document provides guidelines for a uniform system for grouping materials for welding purposes. It can also be applied for other purposes such as heat treatment forming and non-destructive testing. It covers grouping systems for the following standardized materials: - steels; - aluminium and its alloys; - copper and its alloys; -- nickel and its alloys; titanium and its alloys; -- zirconium and its alloys; iTehSTANDARDPREVIEW -cast irons. (standards.iteh.ai) 2Normativereferences ISO/TR 15608:2017 There are no normative references in.this.docuimentsu/S86d8831-2332-4fc8-9d74- 820bfb682c96/so-tr- 15608-2017 3Termsand definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: - IEC Electropedia: available at ISo Online browsing platform: available at 4Grouping system for steels specifications should be considered. Ladle (or heat) analyses should be used in preference of product analysis when both are specified. The figures given in groups: - 1 2 3 and 11 refer to the chemical position specified in the material standard (specified values); - 4 to 10 are based on the elemental content used in the designation of the alloys. Materials assigned to a group in ISO/TR 20172 ISO/TR 20173 and ISO/TR 20174 should be considered assigned to those groups by this document. For materials that are not assigned to a group the criteria of this document apply. @ ISO 2017 All rights reserved
ISO TR 15608-2017 焊接-金属材料分类系统的指南(英文版).pdf
