INTERNATIONAL STANDARD
ofsoundinsulationofbuilding Acoustics-Laboratorymeasurement elements-
Part 2: Measurementofairbornesound insulation
Acoustique Mesurage en laboratoire de lisolation acoustique deselements de construction
Partie 2: Mesurage de I’isolation gu bruit aerien
COPYRIGHTPROTECTEDDOCUMENT
@ ISO 2021
All rightsreservedUless otherwise specified rrequired in the context ofits imlementationno part of this publicationmaybe reproduced or utilized otherwise in any form or by any means electronic or mechanical including photocopying or posting on the internet or an intranet without prior written permission Permission can be requested from either ISO at the addressbelow or ISO's member body in the country of the requester.
ISO copyright officeCP 401 Ch. de Blandonnet 8 CH-1214 Vernier GenevaEmail: copyright@ Phone: 41 22 749 01 11Website: in Swritzerland
Contents
Page
Foreword. ivIntroduction. V1 Scope. 12 Normative references 13 Terms and definitions. 14 Facilities and equipment. 35 Test procedure and evaluation 5.1 General procedure. 3 35.2 Data processing Sound field in the source room. 45.3 5.4 Expression of results. 4 46 Test arrangement. 56.1 6.2 Full-size test opening General. 5 56.3 6.4 Reduced-size test opening Reduced-size test elements. 6 66.5 Small technical elements. 6Limits of performance. Full-size openings 77.1 7.2 Reduced-size openings. 7 78 Measurement uncertainty. .89 Test report. 8Annex A (normative) Measurement of sound transmission through the filler wall and any flanking construction for small-sized or reduced-size test openings. 6Annex B (informative) Form for the expression of results 11Bibliography 14
Foreword
bodies (ISO member bodies). The work of preparing International Standards is normally carried outthrough ISO technical mittees. Each member body interested in a subject for which a technical mittee has been established has the right to be represented on that mittee. Internationalorganizations governmental and non-governmental in liaison with ISO also take part in the work.electrotechnical standardization. ISO collaborates closely with the International Electrotechnical Commission (lEC) on all matters of
The procedures used to develop this document and those intended for its further maintenance aredescribed in the ISO/IEC Directives Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with theeditorial rules of the ISO/IEC Directives Part 2 (see org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject ofany patent rights identified during the development of the document will bein the Introduction and/oron the ISo list of patent declarations received (see -Org/patents).
Any trade name used in this document is information given for the convenience of users and does notconstitute an endorsement.
For an explanation of the voluntary nature of standards the meaning of ISO specific terms andexpressions related to conformity assessment as well as information about ISO's adherence to theiso/foreword.html.
This document was prepared by Technical Committee ISO/TC 43 Acoustics Submittee SC 2 Building acoustics in collaboration with the European Committee for Standardization (CEN) TechnicalAgreement on technical cooperation between ISO and CEN (Vienna Agreement).
revised.
The main changes pared to the previous edition are as follows:
- all references in the text have been updated; in Clause 2 the normative references have been updated;- in Clause 3 the terms and definitions have been updated;- in Clause 8 the title has been changed to "Measurement uncertainty"
A list of all parts in the ISO 10140 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user's national standards body. Aplete listing of these bodies can be found at
Introduction
ISO 10140 (all parts) concerns laboratory measurement of the sound insulation of building elements(see Table 1).
ISO 10140-1 specifies the application rules for specific elements and products including specificrequirements for the preparation and mounting of the test elements and for the operating and test conditions. This document and ISO 10140-3 contain the general procedures for airborne and impactsound insulation measurements respectively and refer to ISO 10140-4 and ISO 10140-5 where appropriate. For elements and products withouta specific application rule described in ISO 10140-1 it ispossible to apply this document and ISO 10140-3. ISO 10140-4 contains basic measurement techniquesISO 10140 (all parts) see Table .1 and processes. ISO 10140-5 contains requirements for test facilities and equipment. For the structure of
ISO 10140 (all parts) was developed to improve the layout for laboratory measurements ensurein laboratory and field measurements. ISO 10140 (all parts) aims at presenting a well-written and arranged format for laboratory measurements.
ISO 10140-1 is planned to be updated with application rules for other products.
Table 1 - Structure and contents of ISO 10140 (all parts)
Relevant partof Main purpose contents and use Detailed contentISO 10140 Appropriate references to ISO 10140-2 andISO 10140-1 It indicates the appropriate test procedure for elements and products. For certain types ISO 10140-3 and product-related specific andtional and more specific instructions about of element/product it can contain addi- additional instructions on: specific quantities measured;quantities and test element size and about size of test element;tions. Where no specific details are includ- ed the general guidelines are according to boundary and mounting conditions;ISO 10140-2 and ISO 10140-3. conditioning testing and Seadoconditions;additional specifics for test report.1SO 10140-2 It gives a procedure for airborne sound insu- lation measurements according to ISO 10140- Definitions of main quantities measured4 and ISO 10140-5. For products without specific application rules it is sufficiently General mounting and boundary conditionsplete and general for the execution of General measurement proceduremeasurements. However for products with specific application rules measurements Data processingare carried out according to ISO 10140-1 if available. Test report (general points)ISO 10140-3 It gives a procedure for impact sound insula- tion measurements according to ISO 10140- Definitions of main quantities measured4 and ISO 10140-5. For products without General mounting and boundary conditionsspecific application rules it is sufficiently plete and general for the execution of General measurement proceduremeasurements. However for products with specific application rules measurements Data processingare carried out according to ISO 10140-1 if available. Test report (general points)