BRITISH STANDARD BS EN 1337-4:2004 Incorporating corrigendum no.I Structural bearings- Part 4:Roller bearings The European Standard EN 1337-4:2004 has the status of a British Standard ICS91.010.30 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Copyright Brtish Standards ins British Standards BSEN1337-4:2004 National foreword This British Standard was published by BSI.Itisthe UKimplementation of EN 1337-4:2004 incorporating corrigendum February 2007.Together with BS EN 1337-6:2004 it supersedes BS 5400-9.1:1983 which will remain current until the publication of the remaining parts of the BS EN 1337 series. The UK participation in its preparation was entrusted to Technical Committee B/522 Structural bearings. A list of organizations represented on this mittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication This British Standard was Amd.No. Date Comments published under the authority of the Standards Policy and 17035 30 March 2007 Cross-reference to EN 1337-1:2000 deleted Strategy Committee on Corrigendum No.1 28July2004 from final paragraph of 6.7.1 C BSI 2007 ISBN0580441172 Copyright Brtish Standards EUROPEAN STANDARD EN1337-4 NORME EUROPEENNE EUROPAISCHE NORM April 2004 ICS91.010.30 Incorporating corrigendum February 2007 English version Structural bearings Part 4:Roller bearings Appareils d'appui structuraux-Partie 4:Appuis a rouleau Lager im Bauwesen Teil 4:Rollenlager This European Standard was approved by CEN on 2 February 2004. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning suc...

BRITISH STANDARD BS EN 1337-3:2005 Structural bearings- Part 3:Elastomeric bearings The European Standard EN 1337-3:2005 has the status of a British Standard ICS91.010.30 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Coovright British Standards British Standards BSEN1337-3:2005 National foreword This British Standard was published by BSI.It is the UK implementation of EN 1337-3:2005.It partially supersedes BS 5400-9-1:1983 and BS 5400-9-2:1983 which will remain current until the remaining parts of the BS EN 1337 series have been published the last part being Part 8. The UK participation in its preparation was entrusted to Technical Committee B/522 Structural bearings. A list of organizations represented on B/522 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was Amendments issued since publication published under the authority of the Standards Policy and Strategy Committee Amd.No. Date Comments on 29 December 2006 BSI 2006 ISBN0580498506 Coovright British Standards EUROPEAN STANDARD EN1337-3 NORME EUROPEENNE EUROPAISCHE NORM March 2005 ICS91.010.30 English version Structural bearings-Part 3:Elastomeric bearings Appareils d'appui structuraux Partie 3:Appareils d'appui Lager im Bauwesen-Teil 3:Elastomerlager en elastomere This European Standard was approved by CEN on 4 June 2004. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references conceming such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English French ...

BRITISH STANDARD BS EN 1337-2:2004 Structural bearings- Part 2:Sliding elements The European Standard EN 1337-2:2004 has the status of a British Standard ICS91.010.30 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Copyright Brtish Standards ins British Standards BSEN1337-2:2004 National foreword This British Standard was published by BSI.It is the UK implementation of EN 1337-2:2004.It supersedes BS EN 1337-2:2001 which is withdrawn.It partially supersedes BS 5400-9-1:1983 and BS 5400-9-2:1983 which will remain current until the remaining parts of the BS EN 1337 series have been published the last part being Part 8. The UK participation in its preparation was entrusted to Technical Committee B/522 Structural bearings. A list of organizations represented on B/522 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was Amendments issued since publication published under the authority of the Standards Policy and Strategy Committee Amd.No. Date Comments on 29 December 2006 BSI 2006 ISBN0580498492 Copyright Brtish Standards EUROPEAN STANDARD EN1337-2 NORME EUROPEENNE EUROPAISCHE NORM March 2004 ICS91.010.30 Supersedes EN 1337-2:2000 English version Structural bearings Part 2:Sliding elements Appareils d'appui structuraux Partie 2:Elements de Lager im Bauwesen-Teil 2:Gleitteile glissement This European Standard was approved by CEN on 2 January 2004. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Europe...

BRITISH STANDARD BS EN 12620:2002 A1:2008 Incorporating corrigendum May 2004 Aggregates for concrete ICS91.100.15;91 100.30 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Coovright British Standards British Standards rowided by IHS under icense with BSI Uncontrolled Copy No eproduction or networking wihout loonse from IHS Not for Rosale BSEN12620:2002A1:2008 National foreword This British Standard is the UK implementation of EN 12620:2002A1:2008 incorporating corrigendum May 2004.It supersedes BS EN 12620:2002 which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags.Tags indicating changes to CEN text carry the number of the CEN amendment.For example text altered by CEN amendment A1 is indicated by A)A. EN 12620:2002 is included in a package of new European Standards being prepared by CEN/TC 154 relating to aggregates.Although the English text versions of these European Standards will be adopted as British Standards as they bee available the existing British Standards for aggregates will be retained but only until such time that the pleted package of European Standards bees available.The original group of British Standards will then be withdrawn and this will be noted in Update Standards. The UK participation in its preparation was entrusted by Technical Committee B/502 Aggregates to Submittee B/502/2 Aggregates for concrete including those for roads and other pavements. A list of organizations represented on this submittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was Amendments/corrigenda issued since publication published under the authority of the Standards Policy and Strategy Committee Amd.No. Date Comments on 7 Oc...

BSEN12504-2:2021 BSI Standards Publication Testing concrete in structures Part 2:Non-destructive testing-Determination of rebound number bsi. BSEN12504-2:2021 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 12504-2:2021.It supersedes BS EN 12504-2:2012 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/517/1 Concrete production and testing. A list of organizations represented on this mittee can be obtained on request to its mittee manager. The UK mittee draws users'attention to informative National Annex NA appended at the back of this document which offers guidance on the use of this standard. Contractual and legal considerations This publication has been prepared in good faith however no representation warranty assurance or undertaking (express or implied)is or will be made and no responsibility or liability is or will be accepted by BSI in relation to the adequacy accuracy pleteness or reasonableness of this publication.All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law. This publication is provided as is and is to be used at the recipient's own risk. The recipient is advised to consider seeking professional guidance with respect to its use of this publication. This publication is not intended to constitute a contract.Users are responsible for its correct application. ©The British Standards Institution2021 Published by BSI Standards Limited 2021 ISBN9780539053494 ICS91.100.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2021. Amendments/corrigenda issued since publication Date Text affected EUROPEAN STANDARD EN12504-2 NORME EUROPEENNE EUROPAISCHE NORM July 2021 ICS91.100.30 Supersedes EN 12504-2:2012 English Version Testing concrete in structures-Part 2:Non...

BSEN12504-1:2019 BSI Standards Publication Testing concrete in structures Part 1:Cored specimens-Taking examining and testing in pression bsi. Copyright British Standands rsttution Licensee=Shenzhen of Standands and Technology 9072181 Provided by IHS Markit under icense with BSI-Uncontroled Copy Not5 or Resale.20203/110356:23 No reproduction or networking permitted wthout loense from IHS BSEN12504-1:2019 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 12504-1:2019.It supersedes BS EN 12504-1:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/517/1 Concrete production and testing. A list of organizations represented on this mittee can be obtained on request to its secretary. The UK mittee has identified that EN 12390-7 Testing hardened concrete-Part 7:Density of hardened concrete which is listed in the bibliography of EN 12504-1:2019 should be listed in the normative references section Clause 2. It is the opinion of the UK mittee that it is likely that the standard was not listed as a normative reference because Subclause 7.2 mistakenly refers to EN 12390-5 where it should refer to EN 12390-7 because EN 12390-7 is the test method for testing density of hardened concrete and density is the property that is being referred to. The UK mittee also draws users'attention to informative National Annex NA appended at the back of this document which offers guidance on the use of BS EN 12504-1:2019. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. ©The British Standards Institution2019 Published by BSI Standards Limited 2019 ISBN9780580984365 ICS91.100.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2019. Amendments/corrigenda issu...

BS EN 12390-8:2019 EUROPEANSTANDARD EN12390-8 NORMEEUROPEENNE EUROPAISCHENORM June 2019 ICS 91.100.30 Supersedes EN 12390-8:2009
English Version Testinghardenedconcrete-Part8:Depthofpenetration ofwaterunderpressure Essais pour beton durci Partie 8 : Profondeur de Prifung von Festbeton - Teil 8: Wassereindringtiefe unter Druck penetration d'eau sous pression This European Standard was approved by CEN on 29 April 2019. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationa standards may be obtained on aplication to the CEN-CENELEC Management Centre or to any CEN member. q pe ene ao ue u uosa y (ua a ) ssaa eo a u sisxa peps uadng s Centre has the same status as the official versions. translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Finland FraGy e, gary, ln, , tal,atviaLiniamMt, CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Poland, Portugal, Republic f orth Macedonia Romania, Serbia, Sovakia, Slovenia pain, weden, Switzerland,Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels @ 2019 CENworlidwide for CEN national Members. All rights of exploitation in any form and by any means reserved Ref No. EN 12390-B:2019 E
BS EN 12390-8:2019 EN 12390-8:2019 (E)
Contents Page European foreword. 1Scope..5 2Normative references.5 3Terms and definitions..5 4Principle...5 5Apparatus..5 6Specimen..6 7Procedure.7 7.1Preparation of the test specimen.7 7.2Application of water pressure.7 7.3Examination of specimen.7 8Test result.7 9Test report.7 10Precision..8
BS EN 12390-8:2019 EN 12390-8:2019 (E)
Europeanforeword This document (EN 12390-8:2019) has been prepared by Technical Committee CEN/TC 104 “Concrete and related products", the secretariat of which is held by SN.
identical text or by endorsement, at the latest by December 2019, and conficting national standards shall be withdrawn at the latest by December 2019.
patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12390-8:2009. The standard has been restricted to tests on specimens cured in water. This standard is one of a series on testing concrete. EN 12390, Testing hardened concrete, consists of the following parts: --Part 1: Shape, dimensions and other requirements of specimens and moulds; -Part 2:Making and curing specimens for strength tests; --Part 3: Compressive strength of test specimens; --Part 4:Compressive strength Specification for testing machines; --Part 5: Flexural strength of test specimens; --Part 6: Tensile splitting strength of test specimens; --Part 7: Density of hardened concrete; -Part 8: Depth of penetration of water under pressure; -Part 11: Determination of the chloride resistance of concrete, unidirectional diffusion; -Part 12: Determination of the potential carbonation resistance of concrete: Accelerated carbonation method (in preparation); -Part 13: Determination of secant modulus of elasticity in pression; Part 14: Semi-adiabatic method for the determination of heat released by concrete during its hardening process; -Part 15: Adiabatic method for the determination of heat released by concrete during its hardening -Part 16: Determination of the shrinkage of concrete (in preparation); --Part 17: Determination of creep of concrete in pression (in preparation);:
3
BS EN 12390-8:2019 EN12390-8:2019 (E)
-Part 18: Determination of the chioride migration coefficient (in preparation). This edition includes the following significant technical changes with respect to EN 12390 8:2009: -editorial revision. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
BS EN 12390-8:2019 EN 12390-8:2019 (E)
1Scope This document specifies a method for determining the depth of penetration of water under pressure in hardened concrete which has been water cured. 2Normativereferences The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referen...

BSEN12390-2:2019 BSI Standards Publication Testing hardened concrete Part 2:Making and curing specimens for strength tests bsi. BSEN12390-2:2019 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 12390-2:2019.It supersedes BS EN 12390-2:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/517/1 Concrete production and testing. A list of organizations represented on this mittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. ©The British Standards Institution2019 Published by BSI Standards Limited 2019 ISBN9780580984372 ICS91.100.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2019. Amendments/corrigenda issued since publication Date Text affected EUROPEAN STANDARD EN12390-2 NORME EUROPEENNE EUROPAISCHE NORM June 2019 ICS91.100.30 Supersedes EN 12390-2:2009 English Version Testing hardened concrete Part 2:Making and curing specimens for strength tests Essais pour beton durci-Partie 2: Prufung von Festbeton-Teil 2:Herstellung Confection et conservation des eprouvettes und Lagerung von Probekorpern pour essais de resistance fur Festigkeitsprufungen This European Standard was approved by CEN on 29 April 2019. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English French German).A version in any other language made by translati...

BRITISH STANDARD BS EN 1092-3:2003 Incorporating Corrigendum No.1 Flanges and their joints-Circular flanges for pipes valves fittings and accessories PN designated- Part 3:Copper alloy flanges The European Standard EN 1092-3:2003 has the status of a British Standard ICS23.040.60 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards BSEN1092-3:2003 National foreword This British Standard is the official English language version of EN 1092-3:2003 including Corrigendum July 2004.It supersedes BS 4504-3.3:1989 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PSE/15 Flanges which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European mittee any enquiries on the interpretation or proposals for change and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this mittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled"International Standards Correspondence Index" or by using the“Search"facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This British Standard.was This document prises a front cover an inside front cover the EN title page published under the authority pages 2 to 35 and a back cover. of the Standards Policy and Strategy Committee on The BSI copyright notice displayed in this document indicates when the 8 March 2004 document was last issued. Amendments issued si...

STD.BSI BS EN1092-2-ENGL199716246b90639139160 ■ BRITISH STANDARD BS EN 1092-2:1997 Flanges and their joints- Circular flanges for pipes valves fittings and accessories PN designated Part 2.Cast iron flanges 40 The European Standard EN 1092-2:1997 has the status of a British Standard ICS23.040.60 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW 丰S STD.BSI BS EN 1092-2-ENGL 1997 162466906391409T2 BSEN1092-2:1997 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PSE/15 Flanges upon which the following bodies were represented: British Compressed Gases Association British Foundry Association British Iron and Steel Producers'Association British Malleable Tube Fittings Association British Plumbing Fittings Manufacturers'Association British Pump Manufacturers'Association British Valve and Actuator Manufacturers'Association Confederation of British Forgers Copper Development Association Energy Industries Council Engineering Equipment and Materials Users'Association GAMBICA (BEAMA Ltd.) Power Generation Contractors Association (PGCA (BEAMA Ltd.)) This British Standard having been prepared under the direction of the Sector Board for Engineering was published under the authority of the Standards Board and es into effect on 15 September 1997 BSI 1997 Amendments issued since publication Amd.No. Date Text affected The following BSI references relate to the work on this standard Committee reference PSE/15 Draft for ment 93/707537 DC ISBN0580279626 一 STD.BSI BS EN 1092-2-ENGL 1997 16246690639141839 BSEN1092-2:1997 Contents Page Committees responsible Inside front cover National foreword i Foreword 2 Text of EN 1092-2 3 BSI 1997 i STD.BSI BS EN 1092-2-ENGL 1997 16246690639142775 BSEN1092-2:1997 National foreword This Part of BS EN 1092 has been prepared by Technical Committee PSE/15 and is the English language version of EN 1092-2:1997 Flanges and their joints-Circular flanges fo...

BSEN1092-1:2018 BSI Standards Publication Flanges and their joints Circular flanges for pipes valves fittings and accessories PN designated Part 1:Steel flanges bsi. BSEN1092-1:2018 BRITISH STANDARD National foreword This Published Document is the UK implementation of EN 1092-1:2018.It supersedes BS EN 1092-1:2007A1:2013 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PSE/15 Flanges. A list of organizations represented on this mittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. ©The British Standards Institution2018 Published by BSI Standards Limited 2018 ISBN9780580931062 ICS23.040.60 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 30 April 2018. Amendments/corrigenda issued since publication Date Text affected BSEN1092-1:2018 EUROPEAN STANDARD EN1092-1 NORME EUROPEENNE EUROPAISCHE NORM April 2018 ICS23.040.60 Supersedes EN 1092-1:2007A1:2013 English Version Flanges and their joints-Circular flanges for pipes valves fittings and accessories PN designated-Part 1:Steel flanges Brides et leurs assemblages-Brides circulaires pour Flansche und ihre Verbindungen-Runde Flansche fur tubes appareils de robinetterie raccords et Rohre Armaturen Formstucke und Zubehorteile nach accessoires designees PN Partie 1:Brides en acier PN bezeichnet-Teil 1:Stahlflansche This European Standard was approved by CEN on 27 November 2017. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC...

BRITISH STANDARD BS EN 10311:2005 Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids The European Standard EN 10311:2005 has the status of a British Standard IC823.040.60 BSi Copyright Brtah Standanda instuto NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW uood by IHS undor loonss with BSI-Unoontroled Copy British Standards No or networking permited wthout earse from Nof for Resale BSEN10311:2005 National foreword This British Standard is the official English language version of EN 10311:2005.It partially supersedes BS 534:1990 and supplements EN10224:2004. The UK participation in its preparation was entrusted to Technical Committee ISE/8 Steel pipes which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European mittee any enquiries on the interpretation or proposals for change and keep the UK interests informed; -monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this mittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled“International Standards Correspondence Index" or by using the“Search"facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard does not ofitself confer immunity from legal obligations. Summary of pages This document prises a front cover an inside front cover the EN title page pages 2 to 27 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This British Standard was Amendments issued since publication pu...

BRITISH STANDARD BS EN 10300:2005 Steel tubes and fittings for onshore and offshore pipelines- Bituminous hot applied materials for external coating The European Standard EN 10300:2005 has the status of a British Standard ICS23.040.9925.220.60;75.180.10 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Not for Rinsaio BSEN10300:2005 National foreword This British Standard was published by BSI.It is the UK implementation of EN 10300:2005.It supersedes BS 4147:1980 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee ISE/16 Protective coatings and linings of metal pipes and fittings to Submittee ISE/16/-/11 External coatings for steel tubes and fittings. A list of organizations represented on ISE/16/-/11 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was Amendments issued since publication published under the authority of the Standards Policy and Strategy Committee Amd.No. Date Comments on 29 December 2006 BSI2006 ISBN0580498778 No ction cr notworkin oormitod wthout from IHS Not for EUROPEAN STANDARD EN10300 NORME EUROPEENNE EUROPAISCHE NORM November 2005 ICS23.040.99:25.220.60:75.180.10 English Version Steel tubes and fittings for onshore and offshore pipelines- Bituminous hot applied materials for external coating Tubes en acier et raccords pour canalisations enterrees et Stahlrohre und -formstlicke fur erd-und wasserverlegte immergees Revetements externes au moyen de Rohrleitungen Werksumhullungen aus heis materiaux hydrocarbones aufgebrachtem Bitumen This European Standard was approved by CEN on 25 March 2005. CEN members are bound to ply with the CEN/CENELEC Intemal Regulations which stipulate the conditions for giving this European St...

BSEN10293:2015 BSI Standards Publication Steel castings-Steel castings for general engineering uses bsi. ..making excellence a habit. BSEN10293:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 10293:2015.It supersedes BS EN 10293:2005 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/111 Steel Castings and Forgings. A list of organizations represented on this mittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. @The British Standards Institution 2015.Published by BSI Standards Limited 2015 ISBN9780580772283 ICS77.140.80 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2015. Amendments issued since publication Date Text affected BSEN10293:2015 EUROPEAN STANDARD EN10293 NORME EUROPEENNE EUROPAISCHE NORM January 2015 ICS77.140.80 Supersedes EN10293:2005 English Version Steel castings-Steel castings for general engineering uses Aciers moules -Aciers moules d'usage general Stahlguss-Stahlguss fur allgemeine Anwendungen This European Standard was approved by CEN on 5 December 2014. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerming such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English French German).A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the ...

BRITISH STANDARD BS EN 10278:1999 Dimensions and tolerances of bright steel products The European Standard EN 10278:1999 has the status of a British Standard ICS77.140.60 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW S Copyright Brtish Standands BSEN10278:1999 National foreword This British Standard is the English language version of EN 10278:1999.Together with BS EN 10277 parts 1 to 5 this standard supersedes BS 970-3:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/31 Wrought steels which has the responsibility to: -aid enquirers to understand the text; -present to the responsible European mittee any enquiries on the interpretation or proposals for change and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this mittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled"International Standards Correspondence Index" or by using the “Find"facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract.Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document prises a front cover an inside front cover the EN title page pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This British Standard having Amendments issued since publication been prepared under the direction of the Engineering Amd.No. Date Comments Sector Committee was published under the authority of the Standards Committee and es int...

BSEN10277:2018 BSI Standards Publication Bright steel products-Technical delivery conditions bsi. Copyright Brtish Standards Institution BSEN10277:2018 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 10277:2018. It supersedes BS EN 10277-1:2008 BS EN 10277-2:2008 BSEN10277-3:2008 BSEN10277-4:2008 and BS EN10277-5:2008 which are withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/105 Steels for Heat Treatment Alloy Steels Free-Cutting Steels and Stainless Steels. A list of organizations represented on this mittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. ©The British Standards Institution2018 Published by BSI Standards Limited 2018 ISBN9780580968471 ICS77.140.60;77.140.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018. Amendments/corrigenda issued since publication Date Text affected Copyright British Standards Insttution BSEN10277:2018 EUROPEAN STANDARD EN10277 NORME EUROPEENNE EUROPAISCHE NORM June 2018 ICS77.140.10:77.140.60 Supersedes EN10277-1:2008 EN10277-2:2008 EN10277-3:2008 EN10277-4:2008 EN10277-5:2008 English Version Bright steel products-Technical delivery conditions Produits en aciers transformes a froid-Conditions Blankstahlerzeugnisse-Technische Lieferbedinungen techniques de livraison This European Standard was approved by CEN on 20 February 2018. CEN members are bound to ply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Manag...

BSEN10250-4:2021 BSI Standards Publication Open die steel forgings for general engineering purposes Part 4:Stainless steels bsi. BSEN10250-4:2021 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 10250-4:2021.It supersedes BS EN 10250-4:2000 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/111 Steel Castings and Forgings. A list of organizations represented on this mittee can be obtained on request to its mittee manager. Contractual and legal considerations This publication has been prepared in good faith however no representation warranty assurance or undertaking (express or implied)is or will be made and no responsibility or liability is or will be accepted by BSI in relation to the adequacy accuracy pleteness or reasonableness of this publication.All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law. This publication is provided as is and is to be used at the recipient's own risk. The recipient is advised to consider seeking professional guidance with respect to its use of this publication. This publication is not intended to constitute a contract.Users are responsible for its correct application. ©The British Standards Institution2021 Published by BSI Standards Limited 2021 ISBN9780539003918 ICS77.140.20;77.140.85 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2021. Amendments/corrigenda issued since publication Date Text affected BSEN10250-4:2021 EUROPEAN STANDARD EN10250-4 NORME EUROPEENNE EUROPAISCHE NORM May 2021 ICS77.140.20:77.140.85 Supersedes EN 10250-4:1999 English Version Open die steel forgings for general engineering purposes- Part 4:Stainless steels Pieces forgees en acier pour usage general-Partie 4: Freiformschmiedestucke aus Stahl fur allgemeine Aci...

BRITISH STANDARD BS EN 10244-2:2009 Steel wire and wire products-Non- ferrous metallic coatings on steel wire Part 2:Zinc or zinc alloy coatings ICS25.220.40;77.140.65 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Coovriaht Brtish Standards Prowided by IHS under ioense with BSI -Unoontrolled Copy No reproduction or networking wihout ioonse from IHS Not for Rosale BSEN10244-2:2009 National foreword This British Standard is the UK implementation of EN 10244-2:2009.It supersedes BS EN 10244-2:2001 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/26 Steel wire. A list of organizations represented on this mittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard Amendments/corrigenda issued since publication was published under the authority of the Standards Policy and Strategy Date Comments Committee on 31 May 2009. BSI 2009 ISBN9780580626036 Coovriaht British Standards Prowided by IHS under icense with BSI-Uncontrolled Copy No reproduction or networking permitted wihout loense from IHS Not for Rosale BSEN10244-2:2009 EUROPEAN STANDARD EN10244-2 NORME EUROPEENNE EUROPAISCHE NORM April 2009 ICS25.220.40:77.140.65 Supersedes EN 10244-2:2001 English Version Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2:Zinc or zinc alloy coatings Fils et produits trefiles en acier Revetements metalliques Stahldraht und Drahterzeugnisse-Uberzuge aus non ferreux sur fils d'acier Partie 2 Revetement de zinc Nichteisenmetall auf Stahldraht Teil 2:Uberzuge aus Zink ou d'alliage de zinc und Zinklegierungen This European Standard was approved by CEN on 20 December 2008. CEN members are bound to ply with the CEN/CENELEC Intenal ...

BRITISH STANDARD BS EN 10224:2002 Incorporating Corrigendum No.1 and Amendment No.1 Non-alloy steel tubes and fittings for the conveyance of water and other aqueous liquids-Technical delivery conditions The European Standard EN 10224:2002 with the incorporation of amendment A1:2005 has the status of a British Standard ICS23.040.10;23.040.40 BSi wINemNwwY'tr NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards No or networking wthout leense from HS Nof for Resale BSEN10224:2002 National foreword This British Standard is the official English language version of EN 10224:2002 including amendment A1:2005.Together with BS EN 10311 it will supersede BS 534:1990 which will be withdrawn upon publication of BS EN10311. The start and finis hof text introduced or altered by CEN amendment is indicated in the text by tags A)Al.Tags indicating changes to CEN text carry the number of the CEN amendment.For example text altered by CEN amendment Al is indicated by Changes made by CEN letter of correction January 2003 are indicated by a sideline. The UK participation in its preparation was entrusted by Technical Committee ISE/8 Steel pipes to Submittee ISE/8/-/5 Pipes for water and sewage which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European mittee any enquiries on the interpretation or proposals for change and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this submittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled "International Standards Correspondence Index" or by using the“Search'"facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not p...

BSEN10217-1:2019 Incorporating corrigendum May 2019 BSI Standards Publication Welded steel tubes for pressure purposes Technical delivery conditions Part 1:Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties bsi. Copyright British Standards insttution Licensee=Shenzhen of Standards and Technclogy 9072181 Provided by IHS Markst under icense with BSI-Uncontroled Copy Not5 or Resale.20203/1103:18:38 No reproduction or networking permitted wthout loense from IHS BSEN10217-1:2019 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 10217-1:2019.It supersedes BS EN 10217-1:2002 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/110 Steel Tubes and Iron and Steel Fittings. A list of organizations represented on this mittee can be obtained on request to its secretary. BSI as a member of CEN is obliged to publish EN 10217-1:2019 as a British Standard.However attention is drawn to the fact that during the development of this European Standard the UK mittee voted against its approval. The UK mittee draws users'attention to the fact that BS EN 10217 Parts 1 to 7 are product standards and are therefore intended to assist specifiers designers and other users of the documents by setting out a series of tube and pipe grades intended for use in pressure applications. The non-alloy and low-alloy grades in Parts 1 to 6 are parable (interchangeable)with seamless grades of the same designations in BS EN 10216 Parts 1 to 4.Similarly the stainless grades in Part 7 are parable to seamless grades of the same designations in BS EN 10216 Part 5. It should be noted that guidance on material suitability for specific applications is not provided in product standards.It is therefore important that specifiers designers and other users of the documents understand the differences between the types and characteristics of the welded pressure pipes co...