TURKSTANDARDI
Aluminyumve aluminyumalasimlari-Bicimlendirilebilen mamullerden uretilen vurma ekstruzyon taslaklari-Ozellikler
Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products -Specification
Aluminium et alliages daluminium - Pions de filage parchoc obtenus a partir de produits corroyes -Specification
Aluminium und Aluminiumlegierungen - Butzen zumFliefSpressen aus Halbzeug hergestellt -Spezifikation
Milli Onsoz
Bu standard CEN/TC 132 *Aluminium and aluminium alloys-Aluminyum ve aluminyum alasimlan"Teknik Komitesi tarafindan hazirlanmis CEN tarafindan 15.12.2006 tarihinde onaylanmis ve TurkStandardlari Enstitusu Teknik Kurulu'nun 31.01.2008 tarihli toplantisinda Turk Standardi olarak kabuledilerek yayimina karar verilmistir.
Bu standardda kullanilan bazi kelimeler ve/veya ifadeler patent haklarina konu olabilir. Boyle birpatent hakkinin belirlenmesi durumunda TSE sorumlu tutulamaz.
Bu standard yayinlandiginda TS 10320 EN 570:2002 standardinin yerini alir.
CEN yeleri siraslyla Almanya Avusturya Belcika Birlesik Krallk Bulgaristan Cek Cumhuriyeti Kibris Letonya Litvanya Luksemburg Macaristan Malta Norvec Polonya Portekiz Romanya Slovakya Slovenya ve Yunanistan'in milf standard kuruluslaridir.
EN 570
Supersedes EN 570:1994
English Version
Aluminiumand aluminiumalloys-Impactextrusionslugsobtainedfromwroughtproducts-Specification
Aluminium et alliages d'aluminium - Plions de filage parchoc obtenus a partir de produits corroyes - Specilication
Aluminium und Aluminiumlegierungen - Butzen zumFlieSpressen aus Halbzeug hergestelt - Spezifikation
This European Standard was approved by CEN on 15 December 2006.
CEN members are bound to ply with the CEN/CENELEC InternalRegulations which stipulate theconditions for giving this EuropeanStandard the status of a national standard wihoutanyaleration.Uptodate liss and bbliographical references conceming suchational standards may be obtained on application to the CEN Management Centre or to any CEN member.
This EurpeanStandardxistsn three oficial erions Engish FrenchemanAverionnanytherlanguaemadebytranlnunder the responsibility of a CEN member into its own language and notifed to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austia Belgium Bugaria Cyprus Czech Republic Denmark Estonia Finland France Gemay Greece Hngary Icland Ireland laly Lavia Liuania Lxmbourg Mala etherlands oway Poland PotgalRomania Slovakia Slovenia Spain Sweden Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATIONEUROPAISCHES KOMITEE FUR NORMUNG
Management Centre: rue de Stassart 36 B-1050 Brussels
Contents
Foreword.. Scope.2 1 Normative references. 4Terms and definitions .44 Ordering information... ...54.1 4.2 Designation General. .55 Requirements.5.1 5.2 Tolerancesondimensions and form.. Chemical position.. 10 .65.4 5.3 Mechanical properties.. Other requirements. 11 106 Testing.. .116.1 6.2 Chemical position Brinell hardness.. 116.3 Surface quality. 127 Samplingrate and testcertificates. 128 Packaging and marking . .129 Complaints of non-conformity .12
Foreword
This document (EN 570:2007) has been prepared by Technical Committee CEN/TC 132 *Aluminium and aluminiumalloys" the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard either by publication of an identical text orJuly 2007.
This document supersedes EN 570: 1994.
Within its programme of work Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 11 *Slugs for impact extrusion" to revise EN 570: 1994.
The following technical modifications have been introduced during the revision:
- Clause 2: References to EN 754-3 EN 754-7 EN 754-8 EN 755-3 EN 755-7 and EN 755-8 added;-Clause 4:Text modified;Clause 5:Table 4 deleted and replaced by references to EN 755-7 and EN 755-8;-Table 6: Materials EN AW-1090 EN AW-1100 EN AW-3003 EN AW-5251 EN AW-6005A and EN AW-6063 added; materials EN AW-5305 EN AW-5505 and EN AW-5110 deleted.
CEN shall not be held responsible for identifying any or all such patent rights.
CEN/TC 132 affrms it is its policy that in the case when a patentee refuses to grant licences on standardisedstandard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard.
tries are bound to implement this European Standard: Austria Belgium Bulgaria Cyprus Czech Republic Den-Malta Netherlands Norway Poland Portugal Romania Slovakia Slovenia Spain Sweden Switzerland andUnited Kingdom.
