美国HoneywellIntemational Inc.公司
J-SAP-M-M500KC型手动火灾报警按钮 安装、维护及使用说明
总述
件.它是一种专用的编址手动按钮，安装在两总线制通讯电路上，当发现火灾情况时，手动压碎驶编片，监视控制器会发出 J-SAP-M-M500KC型手动火灾报警披钼是为与NOTIFIER公司相容的控制器配套使用而设计的一种火灾控制系统器报警信号，网时手田上的LED灯显示报警状态.
安装条件
用，有关产品建议请找你的供应商.） J-SAP-M-M500KC手动报警按钮可以安裂于正需的室内环场中.它不能用在室外或危险的场合（如果在这些地方使
嵌入式：应选用标准的76x76mm²的预埋盒.水平安装孔距60mm.
安装
注意
或者给系统的任一部分加电.楼线必须符合有关地方和国家法规和标准. 在完成必要的导线极性、电路通路和绝缘检查能，不能将电路导线连接到该手动按钮、其它现场装置或控制器上.
2.拧检前盖下部的照钉，卸下首盖，注意勿将玻痛片脱返，取下皱痛片. 3.按图指定的工程图纸设置手动按钮的地址，一般用平头刀状起子在01一99间将握码开关旋转到指定号码.但根据配套控制器的需要，最大可旋转至159号码（左垃的损码盘为十位数，右地的拨钙盘为个位数）.
4.按如下方式将手动按细模块的两根导线连接到安装盒增子： 通讯回路正线*”：2（）通讯回路负线"：1（一）
5.将于动拉经图定在安装盒里，面意电缓都固定，并有足够的空隙.在手动按链前都放好玻璃，并用前都安装
6.吾手动按钮通讯线极性接反，被反接的手动按祖将无法 工作，但不影响回路中其它产品的工作.
测试
作.此时，控制器上应显示该手钮报火警，手链脂示灯应恒亮以表示手钮功前正常，复位手动按随时，取下测试匙，在控制 测试手动拉扭时，将提供的测试钥匙描入手动按钮右下侧的槽中，玻璃会微倾斜，相当于模仿于动按钮按下玻痛片的换器上使系统复位.
注意：一且调试测试继束，请勿将测试匙遗面在手动按钼上.
机械参数
前视图
电气参数
工作电压： 15-32VDC执行标准： 触点容量： GB 19880-2005 AC250V 3A
认证标志：
产品标签日期码构成说明
质量保证
视图
删视图
静态电流： 200A软件航本： 报警电流： 5mA（LED额定值：最大30mA） A
几周. 产品的日期码由民位数组成：第一位表示生产年份的末位数字，第二位和第三位表示生产的月份，第民位表示当月的第
美国Honeywell International Inc.公司对所生产的于动报警按钮产品实行三年保修，如果是由于人为损坏，使用不当或白行调整改动产品百导致失效的产品，不属于本保修范围，百因此造成的后果美国Honeywell Intermational Inc.公司将 不负责任.
Manual Callpoint J-SAP-M-M500KCAddressable
General
The J-SAP-M-M50oKC is designed to be gsed with the gatible coetrol panel as a ponent of the contro] pauid n uoeuo ajn omi ai uooeisu og sodeo aqeape lu e si i sssboth signaling of alarmto the monitoring control panel and localled indication of activation.
Mounting Arrangements
The J-SAP-M-M50o8C may be installed in a nomal inoermal environmert. I is not intemded for use in an externally exposedor hazandous location (refer to your supplier for product remendatons if these applications should beinvoled).
Flush: W ft to standand 76x76ma? box The mounting space is 60mm.
Installation
Mechanical Specifications
Caution
AI necary wing play ctiuty andlan estsms be cml be cting cuit ig this callpint fld deces col panels er my adiioal sytm cmps. A rings mst m to alable alcodes and national regulations.
1.. Do not disturb the protetive shielding when wiring the terminals. The front over can be remored by loosening the screw undeseath.Note: Do not break or remove the glass. 0psmp dpppd tun the rotary adsess swinches to the allocated number between 01. 99.(Note: Adres 0 set at the facioy is reognized by the panel as a fault conditioe) (High bit on the left: low bit on the right)Connect the two callpoint rires to the mounting bex termina- Is as tlisted below:5. When conecting the callpoint and mounting box together (1 :doo uou () am Negative (-] munication loop: 1 (-1not be affected. Return glass to its original position and close observe the cable entry holes to ensure cable function willIf to be conmected with the polarity reversal wire the the cover by tighteming Testthe srew. callpoint wil not operate normally. But cher units can siloperate as usually i the loop.
Electrical Specification
5mA (LED Rating Max. 30mA) 200A A
1532VDC CB 19880-2005 AC250V 3A
Opeating Voltage:Contact Rating Standard:
Certification:
Product Nameplate Date Code Note
x XX XThe end sumber of fhe peoducing year io piod a Ithe week cf te mot
Test
When to tthe calt int th suled et e i e slt a the bttm rgh hnd ce of e calp Teand the dicatr light cmushy shs hat the calpt Is peating perty. Wh t rese the callpnt pe glas will drop and as the callpoint pesses the glass. At that time the control panel should display the callpoint in alarmremove the test key and reset the system m the cotrol panel.
Three-Year Limited Warranty
Hneywtnlaats l ltml dpepd Warranty shall be limited to the repair or replaoemet of any art of the mmual cllpoint which is foumnd to be defectie in s p oo sed ane yo ep sa jo pod x as pue an u pmmanufacture.
Note: DO NOT leave the test key in the callpoint once the adjustmen /lesting is plete.
