Technicaldrawings- Screwthreadsandthreaded parts
Part2.Screwthreadinserts
This British Standard havingbeen prepared unde the direction of the Engineering Sector Board was publishedStandards Board and es into under the authority of theeffect on 16 Angust 1996
BSI 1996
The following BSI referencesCommteereferenceTDE/4 relate to the work on this standard:August 1996 Draft announced in BS/ Nenes
ISBN 0 890 26186 9
Committeesresponsibleforthis BritishStandard
The preparation of this British Standard was entrusted to Technical Corumittee TDE/4 Engineering drawing practice upon which the following bodies wererepresented:
Atomic Weapons Estabtishment British Gas plcDrawing Omice Material Mamufacturers' and Dealers’ Association British Standards SocietyElectricity AssociationGauge and Tools Makers’Association HEVAC AssociationInstitution of Chemical EngineersInstitution of Engineering Designers Power Generation Contractors’ AssociationSociety of British Aerospace Companies Ltd.University of Warwick
Amendments issued since publieation
Amd. No. Date Text affected
Contents
PageCommittes responsible Inside front coverNational forewordIntroduction Foreword 2 2Specification Scope1 Normative references 3 33 Representation 3Aaex 4 Desigation and dimensioningZA (normative) Normative references to intermational publications with theirrelevant European publications
Nationalforeword
This British Standard has been prepared by Technical CommitteeTDE/ and is theEnglishangungeversonfENISO6410-2:1996Tecicldrngs-SeretrendsCommittee for Standardization (CEN)It is identical with ISO 64102: 1903 published and threded partsPar2:Sere threadinsertspublished bytheEuropeanby the Intemational Organization for Standardization (ISO).
This Britsh Standard prtially supersees BS 308:Part 1. It is envisaed that whn thefull range of European Standards on technical drawing is implemented BS 308 will bewithdrawn.
Cross-references
Publieation referred toEN 20225:1991 (ISO 225: 1983)
BS EN 20225 : 1992 Fasteners. Bolts screws studs and muts. Synbols and designations of dimensionsBS EN ISO 6410 Technical draurings Screne threads and threaded partsBS EN ISO 6410-1 : 1996 General cowtentions
EN ISO 6410-1: 1996 (ISO 6410-1 : 1993)
Compliance with a British Standard does not of itself confer immunityfrom legal obligations.
English version
Technical drawings-Screw threads and threadedparts- Part 2:Screw thread inserts
(ISO 6410-2: 1993)
Dessins techniques - Filetages et piecesfiletees-Partie 2: Inserts filetes (ISO 6410-2 : 1993)
Technische Zeichnungen-Gewinde und Gewindeteile--Tell 2:Gewindeeinslatze (ISO 6410-2: 1993)
This European Standard was approved by CEN on 1996-03-02.CENmembers arebound to plywith the CEN/CENELECIntemalRegulations whichstipulate theconditions forgiving thisEuropeanStandard the status ofa national standard without any alteration.
Up-to-datelistsandbibliographicalreferencesconcemingsuchnationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English French responsibity ofaCENmemberinto its ownlanguage andnotified to the Central German)A versionin any other language made by translation under the
Secretariat has the same status as the official versions.
CEN members are the national standards bodies ofAustriaelgium Denmark Fnland France Gemany.Grece IelandIrelandItaly，Luxmborg NetherlandsNorway PortugalSpain Sweden Switzerland and United Kingom
European Committee for Standardization Comite Europeen de NormalisationEuropisches Komitee fir Normung
Central Secretariat:rue de Stassart 36 B-1050 Brussels
