Technical product documentation- Springs
Part2.Presentationofdatacylindricalhelical pression springs
This British Standard havingbeen prepared under the direction of the Engineering Sector Board was publishedStandards Board and coes into mder the authority of theeffect on 15 November 1996
C BSI 1096
The fotlowing BSI referemces relate to the work on thisCommttee referenceTDE/4 standard:Draft announced in BSF Nencs
ISBN 0 580 26332 0
Committeesresponsibleforthis BritishStandard
The preparation of this British Standard was entrusted toTechnical CommitteeTDE/4 Engineering drawing practice upon which the following bodies were represented:
Atomic Weapons EstablishmentBrtish Gas ple British Standards SocietyElectricity Association Drawing Office Material Manufacturers’ and Dealers' AssociationGauge and Tools Makers' Association HEVAC Association Institution of Chemical EngineersInstitution of Engineering DesignersPower Generation Contractors'Association Society of British Aerospace Companies Ltd.University of Warwick
Amendments issued sinee publication
Amd No. Date Text affected
Contents
PageCommittees responsible National foreword Inside front coverForeword 22 1 Scope Normative references 3Definitions 34 5 Letter symbols Presentation of data 3 3AnnexesA (informative) Example of the presentation of a preprinted data set for a spring 7B (informative) Bibliography 10ZA (notmative) Normative references to intemational publications with their relevant Exuropean publications 11sqoqufs apat pue saaunemed uaisap Supdg2 Types of spring ends 4
Tables
Nationalforeword
Cross-references
Publication referred to
EN ISO 2162-1:1996(ISO 2162-1: 1003)
EN ISO 21623 : 1996(ISO 2162-3 : 1998)
This British Standard has been prepared by Technical Commttee TDE/4 and Is the EnglishlanguageversionofENISO21622:1996TecicalproductdocmenationSpringsPart2:Presentationofdata for eglindril helical pressionsprings published by the European Committee for Standardization(CEN）.It s identical with ISO 2162-2 : 1993 published by the Intemational Organization for Standardization (ISO).
It is envisaged that when the full range of Europeun Standards on technical drawing is implemented BS 308 will be withdrawn.
BS EN ISO 2162-3 : 1996 Voeabulory
Compliance with a British Standard does not of itself confer immunityfrom legal obligations.
ICS 01.100.20; 21.160
English version
Part2:Presentation ofdataforcylindricalhelicalpression Technicalproductdocumentation-Springs- springs
(ISO 2162-2 : 1993)
Documentation techunique de produits Ressorts-Partie 2: Presentation des dornees techriquesdes ressorts cylindriques de pression (ISO 2162-2 : 1993)
Federm- Techunische Produktdokurnentation -Teil 2: Angaben ftur zylindrischeSchraubendruckfedem (ISO 2162-2 : 1993)
This European Standard was approved by CENon1996-03-02CENmembers are bound to ply with the CEN/CENELECIntemal Regulations which stipulate theconditions for giving this European Standard the stabus of a national standard without any alteration.
may be obtained on application to the Central Secretariat or to any CEN member. Up-to-date lists and bibliographical references concerming such national standardsGerrnan)A version in anyother laguge made by traunslation under the responsibility of a CENmember into its own language and notified to the CentralSecretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria Belgium Denmark FinlandFrance Germany Greece Iceland Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland and United Kingdom.
European Committee for StandardizationEuropisches Komitee fir Normung Comite Europeen de Normalisation
Central Secretariat: rue de Stassart 36 B-1050 Brussels
