Technical drawings- Rollerbearings
Part2.Detailedsimplifiedrepresentation
This British Suandard havingbeen prepared under the direction of the Engineering Sector Bord was publishedunder the authority of he Staedards Board and es intoeffect on 15 December 1997
BSI 1997
Nationalforeword
Cross-references
Summnry of pages
Amendmentsissued since publication
This British Standard is the English language version of EN ISO 8826-2: 1997. It isidentical with ISO 8826-2 : 1994.
The UK participation in its preparation was entrusted to Technical Committee TDE/4Engineering drawingMetrologPrecisionmeasurement and all relateddocumentation which has the responsibility to:
aid enquirers to understand the text;-present to the responsible intemational/European mittee any enquiries on the interpretation or proposals for change and keep the UK interestsinformed;monitor related intermational and European developments and promnlgate them in the UK
A list of organizations represented on this mittee can be obtained onrequest toits secretary.
an annex which lists normative references to intemational publications with their Attention is drawn to the fact that CEN and CENELEC Standards normmally includeintemational or European publications may be found in the BST Standards corresponding European publications. The British Standards which implement theseCatalogue under the section entitledIntemationalStandards Correspondence Index' or by using the Find’ facility of the BSI Standards Electronic Catalogue.
Complianee with a British Standard does not of itself confer immunityfrom legal obligations.
This document riseafrontcover aninsidefrontcover thENISOtiteae the ENISforewordpage the ISO titlepageages lind ii a blank pagepages to 10 the annex ZA page a blank page an inside back cover and a back cover.
Amd. No. Date Text affected
ENISO8826-2
Descriptors:See ISO document ICS 01.100.20; 21.100.20
English version
Technical drawings-Rollingbearings-Part 2:Detailedsimplifiedrepresentation(ISO8826-2:1994)
Represntation simpie priouliere (ISO 8826-2:1994) Dessins technigues-Roulements-Parte2:
Technieche Zeichnungen-Walzlager-Tell 2:Detaillete vereinlache Darestellung (ISO a826-2:1994)
This European Standard was approved by CEN on 12 September 1997.
Stndnnndaduyangrngs CENmemearounomywtheCENCENELECtemegultonhichsipulatthnlnfrgivingiEurpnstanderde may be obtainedi on applicetion to the Central Secretarlat orto any CEN member.
ThisEutnrinEFhggnundertherenbity f CENmemberintoitsw language andnctifed ttheCentralSecretarathasth smeuthe officalversions.
CENmmersare teatn standarodisstaBelgumechRpublicenmarkFinlandFranceGmanyleelandIld ty ug rnswayPnwenwdd Knm
Foreword
drawings productdefinition andrelated documentationof theInternationalOrganization for Standardization (ISO) has been taken over as an European Standard by CEN/CS.
ThisEuropeanStandardshallbegiventhe statusofanational standard，eitherbypublicationstandards shall be withdrawn at the latest by April 1998. ofanidenticaltext or by endorsement at the latest byApril 1998 and conflicting national
Czech Republic Denmark Finland France Germany，Greece，lceland Ireland ltaly， Luxembourg Netherlands Norway Portugal Spain Sweden Switzeriand and the UnitedKingdom.
Endorsementnotice
European Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).
INTERNATIONAL STANDARD
First edition1994-09-01
Technical drawings-Rolling bearings-
Part 2: Detailedsimplifiedrepresentation
Dessins techniques - Roulements Partie 2: Reprdsentation simplifiee perticuliere
