IEEE Std C57.13-2016 仪器变压器的要求(英文版).docx

IEEE,std,国外及港澳台标准
文档页数:103
文档大小:1.11MB
文档格式:docx
文档分类:国外及港澳台标准
上传会员:
上传日期:
最后更新:

IEEE Standard Requirements for InstrumentTransformers

IEEEPowerand EnergySociety

Sponsored by theTransformers Committee

IEEE3 Park Avenue New York NY 10016-5997USA

IEEEStandard Requirementsfor InstrumentTransformers

Sponsor

of the TransformersCommitteeIEEEPower and Energy Society

Approved 29 January 2016

IEEE-SA StandardsBoard

Abstract: Electrical dimensional and mechanical characteristics are covered takingtransformers of types generally used in the measurement of electricity and theinterchangeability of equipment covered and to assist in the proper selection of suchdetermination resistance measurements,short-time characteristics temperature phase angle demagnetization impedance and excitation measurements polarityrise tests dielectric tests and measurement of open-circuit voltage of currenttransformers.

Keywords:accuracy.current transformer IEEE C57.13 instrument transformer primary winding. rated secondary voltage routine tests secondary winding. typetests voltage transformer

Copyright 2016 IEEE. All rights reserved. 2

Important Notices and Disclaimers Concerning IEEE Standards Documents

IEEE documents are made available for use subject to important notices and legal disclaimers. These notices and disclaimers or a reference to this page appear in all standards and may be found under theDocuments."

NoticeandDisclaimerofLiabilityConcerning theUseof IEEEStandards Documents

IEEE Standards documents standards remended practices and guides) both full-use and trial-use are developed within IEEE Societies and the Standards Coordinating Commitees of the IEEE Standards) u sps yqpdesd dop sVolunteers are not necessarily members of the Institute and participate without pensation from IEEE. brings together volunteers representing varied viewpoints and interests to achieve the final product.While IEEE administers the process and establishes rules to promote faimess in the consensus developmentprocess IEEE does not independently evaluate test or verify the accuracy of any of the information or the soundness of any judgments contained in its standards.

IEEE does not warrant or represent the accuracy or content of the material contained in its standards andexpressly disclaims all warranties (express implied and statutory) not included in this or any other document relating to the standard including but not limited to the warranties of: merchantability; fitnessfor a particular pupose; non-infringement; and quality accuracy effectiveness currency or pleteness of material. In addition IEEE disclaims any and all conditions relating to: results; and workmanlike effort.IEEE standards documents are supplied “AS IS" and *WITH ALL FAULTS."

Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce test measure purchase market or provide other goods and services relatedto the scope of the EEE standard.Furthemore theviewpoint expressed at the time a standard is approvedand issued is subject to change brought about through developments in the state of the art and ments received from users of the standard.

In publishing and making its standards available IEE isnt suggesting or rendering professionl or thrservices for or on behalfof any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document should rely upon hisappropriate seek the advice of a petent professional in determining the appropriateness of a givenIEEE standard.

IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE DATA OR PROFITS; EXEMPLARY OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO:WHETHER IN CONTRACT STRICT LIABILITY OR TORT (INCLUDING NEGLIGENCE ORUPON ANY STANDARD EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION USE OF OR RELIANCEREGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.

Translations

The IEEE consensus development process involves the review of documents in English only. In the eventthat an IEEE standard is translated only the English version published by IEEE should be considered the approved IEEE standard.

资源链接请先登录(扫码可直接登录、免注册)
①本文档内容版权归属内容提供方。如果您对本资料有版权申诉,请及时联系我方进行处理(联系方式详见页脚)。
②由于网络或浏览器兼容性等问题导致下载失败,请加客服微信处理(详见下载弹窗提示),感谢理解。
③本资料由其他用户上传,本站不保证质量、数量等令人满意,若存在资料虚假不完整,请及时联系客服投诉处理。

投稿会员:匿名用户
我的头像

您必须才能评论!

手机扫码、免注册、直接登录

 注意:QQ登录支持手机端浏览器一键登录及扫码登录
微信仅支持手机扫码一键登录

账号密码登录(仅适用于原老用户)