Measurementofairbornenoisefrom hydraulicfluidpowersystems andponents
Part4.Methodofdeterminingsoundpowerlevelsfromvalvescontrollingflowandpressure
Mesurage du brult aerlen emis par les systemes de transmisslons hydraulilques Partie 4.Methode de determinatlon des nlveaux de pulssance acoustlque des appareilsde reglage du deblt et de la presslon
Messung des Luftschalls von Hydrautlikanlagen und-bestandtellenund Drucksteuerung Teil 4. Verfahren zur Bestlmmung der Schalldruckpegel von Ventilen zur DurchfluB-
Contents
ForewordCommittees responsible
Method
0. Introduction 1.Scope2.Definitions 3.Measurement uncerteinty4.Tost onvironment 6. Instrumentation7.Operating conditions 6.Installatlon conditlons for valve8. Location and number of sound measurement 9.Test procedure points11.Calculation ofmean sound presure eve 10. Calculation of valve mean sound pressure levels and sound power levelsatareforenoo distance12. Information to be recorded 13. Test report14. Identification statement
Foreword
This British Standard has been prepared under the direction of the Mechanical Engineering Stancards Committee andisone of group of BritihStandardsrolated to th measurement ofnoisemanating from hydraulicfuidpower systems and ponents. a pnto n snp It is intended that this standard which Is based uponOrgnizatinfStndrdtionwillnifytstngmthds and enable the performanoe of different valves to bepared on a mon basls.
It has been assumed In the drafting of thls British Standard
Appendices
Tablos
Figures
A. Guidance on valve instability andB. Guidance on measuring in an anechoic Its detectlon 6C.Errors and classes of measurement chamber 6 7
1. Standerd deviation of sound power lovel determination3.Flo settings 2. Environmental qualficatlon procedures4.Prossuro sottings 5. Limit of variations in test conditions0. Permissible systematic errors of meesuringinstruments es detorminod during oalibration
1. Example ot test installation in an2.Reletionship betwoen the referenoo box anechoic chamber3. Coiling of retum hose and hemispherical measurement surface 8 f
appropriatelyqualifedandexperienoed peoplefor whom that the executlon of Its provlslons Is entrusted toit has baen prepared.Tho standard prises the following Parts. Pert 1 Method of test for pumpsPart3Guideto theapplicationofPart1andPat2 Part 2 Method of test for motorsFurther Parts are planned.confer immunity from legat obllgations. Complianea with a British Standard does not of itself
British Standard
Measurementofairbornenoisefromhydraulic fluidpowersystemsandponents
Part 4.Method of determining sound power levels from valves controlling flow and pressure
0.Introduction
representing good noise control practice including valveGent factors are eliminated. immediately adjacent to thvalvo.Other syatems depen
Inhydrautlfluldpowerystemspoweris transmittdcircuitValvsareponents whichontrolfiownd and controlled through a liquid under pressure in a closedpressure by providing a variable restriction to the fluid ffoDuringthe processofrestrlctingfow vlaaariableorifitntlrpeertditkinetic energy. If the static pressure of the fluid in thecevitatinacourwhicreCavitn noise in fluid power valves is characterized by a random(and theretore broadband) disturbance with dominant energy levels from around 2 kHz up to and beyond theupper froqueney limits of the humen eerThis sound energycanbetransmittedasfluidbreorstruetureborne noise or radlated as vatve casing airborne nolse.
specfically excluded from the provisions of thistandard. The measurement of valve noise due to instability isGuidence onvalve stabiityanditsdetectinis gvennappendix A. Guidanc is also given in appendix B on measuring In an anechoic chamber.
Accuracy of measurement is divided into thre classes A B and C which are exptalned In appendix C.NOTEThe tltesof the puticatons reerred to in this standard are llsted on the inside back cover.
2.Definitions
For thepuposf thisBritishStandard theollowlngdefinitions apply.
The airborne noise level ofa hydraulic fluid power valveisenimportant considerationin ponent selection It is essential that the noiso measurement tochnigue therefore provides accurate appraisals of these airbornenoise levels.The determination of noise levels is plicated by the interactiont which ooour with thefuid power systemduring noisemeasurementsThe fluid borne and structure borne sound ernergy from the valverise to increased overall noise levels. can be transmitted via the circuit which ultimetely gives
NOTE. Other acoustieal tarms are givan in BS 661.
2.1 free sound fiold. A sound field produced in homogeneous isotropic medium free of boundaries.NOTEnprcticeitisfied in which the ffets f he
boundariaes are nagligiblo ovor the frequtncy renge of interest
2.2 free-field over a reflecting plane.A field produce bya source in the presence of one reflecting plane on which the source Is located.
2.3 reverberant sound field That portion of the sound field inatest room overwhlch theInftuence of soundreoived directly from the source is negligilble.
1.Scope
mination of the sound power levels of a hydraulic fluid This British Standerd describes procedures for the deter-power vatve under controlled conditions of installation and operation suitable for providing a basls for paringthe noise levels of valvos in torms of:
2 4enechoic room A test room having boundaries whichthe frequencv range of interest thereby affording free-field conditions over the measurement surface.
(a) Aweighted sound power level;
2 5 speclal reverberant room. A room having reverberation time/frequency chararacteristics as speclfiedin BS 4196 : Part 3.
(b) octeve bend sound power levels.
From these sound power levelsreference sound pressureelause 11).Forganeral purposos the froquoney renge of levelmay becelculeted forreportingpurpoes seeInterest includes the octave bands with centre frequencies between 125 Hz and 8000 Hz.
2.6mnqre ound psurThe sund prsueaveraged in spaco and time on a mean-square basis.NOTE In practice this is estimated by space and time aering overfinitpethength rvernumberf ftxedmcrophonepositions.
This method is applicable to all types of fluid power apunsn nu o udo c jousteady state conditions irrespootivo of size or specific functionprovied that thenoise levelmeasuredisof the method can bo omplied with. dominantly cavitation noise and the physlcal provisions
s s u (7) ne ounssaud punos us Zlogarithm to thebase 10 of the ratio of the mean-square sound pressure to the squere of the reference soundpressure in decibels (dB).
NOTE The weighting network or the width of the frequeneybandued hould lwybindicd;forexmpeAhtd sound pressure level octave Dend sound pressure level.The referenoe sound pessure is 20 μPa.
The proodures described are intended to measure theairborne noise level obtainable from a valve installation
2.8 sound power leval (L). Tan times the logarithm tosound power in decibels (dB) the bass 10 of the ratio of a given power to the reference
NOTE. The weighting network or the with of the frequency band used shouild alweys be indicated The reference sound power ls 1 pW
2.9 volume of souree under teat. The volume of thohose. envelope of the whole valve and relevant adjacent flexible
2.10 cavitation The formation and collapse of fluidpazjeoo| Aq posneo ping Bujejado ou u) se(jAeo inoden regions of low statio pressure generated by high flowvelocities.
3.Measurement uncertainty
Use methods of measurement which tend to result Instanderd deviations that are equel to or less than thosegiven in table 1. To meet this requirement the methods given in the standards listed In table 2 shall be used.
Table 1.Standard deviation ofsound power level determination
s pg an frequeney of Standard deviationHz 8p250 125 5.0 3.01000 to 4000 000 2.0 2.08000 3.0
NOTE 1 Te standrd devlatlons glven In table 1Inlude theeffects of allowahle variatinns in the positioning of the mnasure- ment points nd in the eiection of any prescribed meaurement surface but exclude varlations In the sound power utput of thesourca from test to toet
NOTE 2. The Aweighted sound power level will In most practicaloes be determined with e stenderd devietion of epproximetely 2 d8.
4.Test environment
4.1 Conduot tosts in onvironmonts that provide “freo-fiold over a reflecting planeor 'special reverberant' conditionsthat meet the environmental qualflcatlon requlrementsdesoribed in BS 4196 : Part 3 and Part 4 (see table 2).
4.2 When more exating evironmental qualiicationprocedures and measurement toohniques are roquired
Table 2. Environmental qualifioation procodures
Method of Test environment Relevant Qualificationmeasurement British Standard proeedere of relevent stemdordEngineering Free-field over a BS 4196 : Part 4 : 1981 Clause 4 andreflecting plane appendix AEngineering Special reverberant BS 4196 : Part 3 : 1981 Clause 4Precision Anechoic BS 4196 :Part 5 : 1961 appendix A Clause 4 andxipuaddPrecision Reverberant BS 4196:Part 2:1961
conduct tests in *anechoic' or 'reverberant’ environments as described in BS 4196 : Part 2 and Part 5.
5.Instrumentation
5.1 Use instrumentation to measure fluid flow fluid pressure and fluid temperature in accordance with
testing i.e ctass C given in appendix C.
5.2 Use instrumentation for scoustical measurements In accordance with BS 5969. This instrumentation shell betable 2 for both performance and calibration. in accordance with the relevant British Standard given in
6.Installation conditions for valvo
prising vlecolledutlethoseandnemetreradls NOTE Figure 1 shows a typloal example of a test installationarray of ten microphones set up in an anechoic chamber.
6.1Valve location. Locate the valve in any positionconsistent with the source Installatlon and measurementsurface (or microphone treverse)requirements specified in the relevant British Standard (seo table 2) for tho testenvironment used.
6.2 Valve mounting
6.2.1 Mount the valve on a vibration isolating mountingso as to minimize the noise radiated by the mounting as a result of valve case vibration
6.2.2 Use a mount whlch provfdes minlmat Interference with the sound radiation from the valve end fluid lines.
valvos in a housing of minimum cize consistent with 6.2.3 Test fine mounting valves as supplied Test cartridgeachieving the flow and pressure ratings of the valve.
jo ujefe oned jodepe ue uo sanjen Bupunou aysef isaminimum sizeWhen velves specificelly desgned forineorporation within a dedicated housing which may formq pe su pnnopue u hose and the whole strueture is carried on isolating mounts
The system omployed shall be doscribed in the test report (see clause 13). Any external control linkages which extendbeyond the volume of the souroe (as defined In 2 9) shall elso inoorporate effotive vibretion isoletion as close tothe valve as possible.
6.3 Fluid supply
6.3 1 Instellthe hydraullio power pock supplying fluid flowand pressure outside the measurement environment or within an acoustic enclosure in such a manner as to controlthe background noise levels to the velues descrilbed in clause 9.
Photogreph by eourteey of BritihMydrautic Research Assoclation
Figure 1. Exemple of test installation in en anechoic chamber
6.3.2 Reduce the fluid borne noise in the high prossure supply line to a level which allows the resulting backgroundandifnecearyprsurrippleattnuatorstoalovlwhch sdund anb fusn Aq g asne u paqosap ou auoqeis in accordance with clause 9. Use at least 15 m of hose betwreen the pump or sifencer and the valve inlet to ensureborne noise. attenuation of high froquency structure borne end fluid
valve before connecting to the return hose. 6.4.6 Fit a rigid olbow directly to the outlet port of the
6.4.7 When measuring in an anechoic chamber coil theminimum bend radius for a peripherel length of at leest1 m. Contain the valve body and a length of 1 m at the beginning of the return hose within the source volumeflexibl supports whichdonotradiatesignificantoie described in BS 4196 : Pert 4 Suspend the hoses oncross overeparatethembyanair gp or intertere with the noise radiation. Where the hosesNOTE Refer to eppendix B for gufdenos
6.4 Hydraulie cireuit
6.4.1Ilinthirit llifit reservoirs pumps and restrictor valves as required to meetthe valve hydraulic operating conditions (see clause 7).
6.4 8 Usua length of at least 15 m of return ine hosebofore connecting it to the beck-pressure control valveor reservoir.
6.4.2 Use test fluid and fitration in accordance with thelines within the measurement environment manufecturer’s instructions Use flexible hose for all fluid
6.4.9 Monitor fluid pressure at the valve inlet and outlotfittings using gauges or transduoers which ply with 5.1 and are mounted outside the noise measuring environment.Use small diameter (1 mm or less)presure tapping which fits flush with the walls of the fittings. Mount the returnline gauge orransuerat thesameheight asthe tapping pointforalbretforanyheightdifference)dpurghose as practicable for the gauge lines. the gauge line of air. Employ as small a diameter flexible
6.4.3 Install hose inlet and outlet sizes which provide maximum velocity of flow below 5 m/s at full rated valve capacity.Connect the hose to the valve ports with theminimum of rigid fittings (see 6.4.6].
.4.4Use ony wire braided rmut-siral syntheticrubber linod hoses. For any hydraulic servo connectionsor leakage lines use as small bore hose as is practicable.
6 4 5 Do not enclose the fluid lines in aooustic materialin the test measurement. as their noise contribution close to the valve is included
6.4.10 Ensure that any valve controlling back-pressureIs stabte In operatlon.
NOTE y ht rd adequate suppressionof flow source ripple is achievedThe noisevatve due to the high frequency attenustion properties of flexible radiatod by the return line ropidly decays with diatence from thehnse.
NOTEaveckpressuhasaprofound effect ncavitatnnoise levels so partieular csre should be taken with the control end moerurement of return line conditions.