INTERNATIONAL STANDARD
Vocabulary-Termsrelatingto Technicalproductdocumentation- technicaldrawings productdefinition andrelateddocumentation
relatifs aux dessins techniques a la definition de produits et α la Documentation technique de produits -Vocabulaire -Termesdocumentation associee
COPYRIGHTPROTECTEDDOCUMENT
@ ISO 2022
Allrights reserved. Uless otherwise specified or required in the context of its imlementation o part of this publication maybe reproduced or utilized otherwise in any form or by any means electronic or mechanical including photocopying or posting on the intermet or an intranet without prior written permission. Permission can be requested from either ISO at the address belowor ISO's member body in the country of the requester.
ISO copyright officeCH-1214 Vernier Geneva CP 401 • Ch. de Blandonnet 8Email:copyright@ Phone: 41 22 749 01 11Website: in Switzerland
Contents
Page
Foreword. iv1 Scope.. 12 Normativereferences. 13 Terms and definitions. 13.1 3.2 Views. General terms.. 11 13.3 3.4 Dimensions. Lines. 173.5 Tolerances.. 203.6 3.7 Graphics. Symbology. 20 213.8 Computer-related terms.. Digital practices. 243.10 3.9 Documentation.. 293.11 3.12 Document management. Writing and marking instruments. 443.13 3.14 Design for manufacturing assembling disassembling and end-of-life processing. 49Bibliography. Information and instructions for use. 55
Foreword
bodies (ISO member bodies). The work of preparing International Standards is normally carried outthrough ISO technical mittees. Each member body interested in a subject for which a technical mittee has been established has the right to be represented on that mittee. InternationalISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of organizations governmental and non-governmental in liaison with ISo also take part in the work.electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance aredifferent types of ISO documents should be noted. This document was drafted in accordance with theeditorial rules of the ISO/IEC Directives Part 2 (see
Attention is drawn to the possibility that some of the elements of this document may be the subject ofpatent rights.ISO shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/oron the ISo list of patent declarations received (see
Any trade name used in this document is information given for the convenience of users and does notconstitute an endorsement.
For an explanation of the voluntary nature of standards the meaning of ISO specific terms andexpressions related to conformity assessment as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
This document was prepared by Technical Committee ISO/TC 10 Technical product documentation inF01 Technical drawings in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 10209:2012) which has been technicallyrevised.
The main changes are as follows:
- certain terms have been added deleted or revised;
- Annex A (deprecated terms) has been deleted.
poq spepus euou sasn au o paap aq pnous uanp s uo suosanb o ppaa uplete listing of these bodies can be found at
relatingtotechnical drawings productdefinitionand Technicalproductdocumentation-Vocabulary-Terms relateddocumentation
1Scope
This document establishes and defines terms used in technical product documentation relating totechnical drawings product definition and related documentation in all fields of application.
The terms have been classified into specific fields of application.
NOTE New terms required by ISO/TC 10 submittees and working groups for new or revised standardswill be ratified by the ISO/TC 10 vocabulary maintenance team and included in future amendments of this document.
2Normativereferences
There are no normative references in this document.
3Terms and definitions
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
ISO Online browsing platform: available at IEC Electropedia: available at
3.1 General terms
3.1.1
activity
processes procedures or parts of them usually related to established organization units
Note 1 to entry: The terms *process" and *procedure* are defined in ISO 9000. A detailed explanation of processes within panies is also given in ISO 9000.
3.1.2 activity matrix
n uoezueo paxg e o pue a a npod go saseud o se ueoe xe
part of the product development process where a specification of requirements is prepared
ancillary system system which is not directly required for the power plant process
rss s s e s sa apressed air supplies fire protection systems cranes elevators workshops and staff amenities.
