ISO 22232-3 2020 无损检测 超声波测试设备的表征和验证 第三部分 组合设备(英文版).pdf

2020年,22232,ISO,pdf,设备,国外及港澳台标准
文档页数:16
文档大小:1MB
文档格式:pdf
文档分类:国外及港澳台标准
上传会员:
上传日期:
最后更新:

INTERNATIONAL STANDARD

Part 3:Combinedequipment

Partie 3: Equipement plet

Non-destructivetesting- Characterizationandverificationof ultrasonictestequipment-

Essais non destructifs - Caracterisation et verification deI'appareillage de controle par ultrasons

COPYRIGHTPROTECTEDDOCUMENT

ISO 2020

Allrights reserved.lesstherwise ecife reqie in the cotext fimlementatin partfths pulicatinmybe reproduced or utilized otherwise in any form or by any means electronic or mechanical including photocopying or posting on the internet or an intranet without prior written permission. Permission can be requested from either ISO at the addressbelow or ISO's member body in the country of the requester.

ISO copyright officeCP 401 • Ch. de Blandonnet 8 CH-1214 Vermier GenevaEmail copyright@ Phone: 41 22 749 01 11Website: in Switzerland

Contents

Page

Foreword iv1 Scope. 12 Normative references 13 Terms and definitions. 14 General requirements for conformity 25 Personnel qualification. 26 Description of tests and reporting. 6.1 Baseline measurements of characteristic values. 2 26.2 Physical state and external aspects. 6.2.1 Procedure.6.2.2 Acceptance criterion. 36.3 Tests for angle-beam probes. 6.2.3 Frequency of testing..6.3.1 6.3.2 Probe index point. General. 3Beam angle. 46.4 Vertical linearity 6.3.4 Simultaneous determination of probe index point and beam angle 6 46.4.1 General. 66.4.2 6.4.3 Acceptance criteria Procedure. 6 76.5 Sensitivity and signal-to-noise ratio. 6.4.4 Frequency of testing. 7 76.5.1 Procedure. General. 76.5.2 6.5.3 Acceptance criterion. 8 86.6 Pulse duration. 6.5.4 Frequency of testing.. 8 86.6.1 General. 86.6.2 6.6.3 Procedure. Acceptance criterion.. 86.6.4 Frequency of testing 6

10

Foreword

bodies (ISO member bodies). The work of preparing International Standards is normally carried outthrough ISO technical mittees. Each member body interested in a subject for which a technical mittee has been established has the right to be represented on that mittee. InternationalISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of organizations governmental and non-governmental in liaison with ISO also take part in the work.electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance aredifferent types of ISO documents should be noted. This document was drafted in accordance with theeditorial rules of the ISO/IEC Directives Part 2 (see

Attention is drawn to the possibility that some of the elements of this document may be the subject ofany patent rights identified during the development of the document willbe in the Introduction and/or patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details ofon the ISo list of patent declarations received (see

Any trade name used in this document is information given for the convenience of users and does notconstitute an endorsement.

For an explanation of the voluntary nature of standards the meaning of ISO specific terms andexpressions related to conformity assessment as well as information about ISo's adherence to theWorld Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see iso/foreword.html.

This document was prepared by ISO/TC 135 Non-destructive testing Submittee SC 3 Ultrasonictesting in collaboration with the European Committee for Standardization (CEN) Technical Committeebetween ISO and CEN (Vienna Agreement). CEN/TC 138 Non-destructive testing in accordance with the Agreement on technical cooperation

A list of all parts in the ISO 22232 series can be found on the ISO website.

poq spreues peuoeu s asn au o paoap aq pinous quaunop su uo suogsanb o yeqpaa uplete listing of these bodies can be found at

Non-destructivetesting-Characterizationand verificationofultrasonictestequipment-

Combinedequipment Part 3:

1 Scope

appropriate standard calibration blocks. of bined ultrasonic test equipment (ie. instrument probes and cables connected) by the use of

These methods are specifically intended for manual test equipment i.e. ultrasonic instrumentsaccording to ISo 22232-1 and for manual ultrasonic non-destructive testing with single- or dual-instruments. For automated test equipment different tests can be needed to ensure satisfactoryperformance.

The specified methods are intended for the use by operators working under site or shop floor conditions.

These methods are not intended to prove the suitability of the equipment for particular applications.

This document excludes ultrasonic instruments for continuous waves.

This document also excludes ultrasonic phased array systems see e. g. ISO 18563-3. If a phased arrayto this bination. instrument is used in bination with single- or dual-transducer probes this document is applicable

2 Normativereferences

The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document (including any amendments) applies.

ISO 2400 Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 1

ISO 5577 Non-destructive testing - Ultrasonic testing - Vocabulary

ISO 7963 Non-destructive testing - UItrasonic testing - Specification for calibration block No. 2

ISO 9712 Non-destructive testing - Qualification and certification of NDT personnel

ISO 22232-1 Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 1: Instruments

ISO 22232-2 Non-destructive testing - Characterization and verification of ultrasonic test equipment -Part 2: Probes

3 Terms and definitions

For the purpose of this document the terms and definitions given in ISO 5577 apply.

资源链接请先登录(扫码可直接登录、免注册)
①本文档内容版权归属内容提供方。如果您对本资料有版权申诉,请及时联系我方进行处理(联系方式详见页脚)。
②由于网络或浏览器兼容性等问题导致下载失败,请加客服微信处理(详见下载弹窗提示),感谢理解。
③本资料由其他用户上传,本站不保证质量、数量等令人满意,若存在资料虚假不完整,请及时联系客服投诉处理。

投稿会员:匿名用户
我的头像

您必须才能评论!

手机扫码、免注册、直接登录

 注意:QQ登录支持手机端浏览器一键登录及扫码登录
微信仅支持手机扫码一键登录

账号密码登录(仅适用于原老用户)