Technicaldrawings-
Representation ofsplines and serrations
The Faropean Standard EN ISO 6413: 1994 has the status of aBritish Standard
Committeesresponsibleforthis British Standard
The preparation of this British Standard was entrusted to Technical CommitteeTDE/4 Engineering drawing practice upon which the following bodles were represented:
Atomic Weapons EstablishmentBrtish Gas plc Brtish Standards SocletyDrawing Omce Material Manufacturers' and Dealers' AsociationGauge and Tool Makers AssociatonHEVAC Association Institution of Chemicai EngineersInstitution of Engineering DesignersPower Generation Contractors'Association Society of British Aerospace Companies IAd.University of Warwick
This Rritish Standard having been prepared under thend peg under the auhority f the direction of the EngineeringStandards Boand and es into effect an15 September 1995
@ BSI 1996
Amendments issued since publication
DateAmd. No. Text affected
The folowing BSI references relate to the work on thisCommitee referenceTDE4 Draft arnounced n BSr Neus standard:August 1995
ISBN 0 580 23774 5
Contents
PageCommittees responsible Inside front coverNational foreword Foreword 2SpecificationScope Normative references 3 82 3 Definitions 34 Designation Compiete representation of spline joints 3 45 6 Simpliffed representation 47 Assermbly drawings 6Annex A (normative） Proportions and dimensions of gmaphical symbols 7TableA.1 1 Dimensions Simplified representation 5
Nationalforeword
EngishlanguageverionofENISO6413:1994TecicaldrwingsRereseatiom This British Standard has been prepared by Technical Committee TDE/4 and is theQfsplines andserrationspublished by theEuropean Commitee forStandardization(CEN). It is identical with ISO 6413 : 1988 published by the Intemational Organization for Standardization (ISO).
fullrange ofEuropean Standaris on technical drawing Is Implemented BS 308 will be This British Standard partially supersedes BS 308 : Part 1. It is envisaged that when thewithdrawn.
Cross-references
Publication referred toISO 14 : 1982
Corresponding British Standard
BS5686:1986Specifioation.for straight-sided splinesforcyindricnlshqftsmetriinal dimensioms tolerances and gauging roquirememntsBS308Engineering drawing practie Part 1:1993Remendatioms for general principlesPart1:1993RecmendtinsforgeralprineiplesPart 1 : 1981 Dimensions and tolerances splines:metric module side fit
ISO 128:1982ISO 4156: 1981 ISO 3098-1: 1974
Compliance with a British Standard does not of itself confer immunity fromlegal obligations.
English verslon
Technical drawings--Representation of splines and serrations
(ISO 6413 : 1988)
Technische Zeichnungen-Darstelung von Keilwellen und Kerbverzahnungen(ISO 6413 : 1988)
Dessins techniques-Representation descannelures et des dentelures (ISO 6413 : 1988)
This European Standard was approved by CEN on 1994-10-14. CEN members areconditions for giving this European Standard the status of a national standardwithout any alteration.
may be obtained on application to the Central Secretariat or to any CEN member Uptodatelits andbibliographical references conceming suchnational standardsThis European Standard exists in three official versions (English French responsibity ofaCENmemberintoitsowlanguageandnotifled to theCentral Secretariat has the same status as the omcialverslons.
CEN members are the national standards bodles of Austrta Belgium Denmark Finland France Geany，Gece lcelandreandItaly，Lumboug Netherlands Norway Portugal Spain Sweden Switzerland and United Kingdom.
European Committee for StandardizationEuropialsches Komitee fur Normung Comite Europeen de Normalisation
Central Secretariat: rue de Stassart 36 B-1050 Brussels
